Kenmore 2214502N020 dishwasher Parts

Yes, repairing a Kenmore dishwasher like model 2214502N020 is worth it when the fix is a common wear part (drain pump, inlet valve, heater, latch) and the total repair cost stays well below the price of a comparable new dishwasher. It is also worth repairing when the stainless steel tub or inner door panel is covered under the limited warranty.

Quick way we decide: repair vs replace

Use these checkpoints before buying parts or scheduling service:

• Age: Dishwashers typically last 9 to 12 years.
• Repair cost: Repair is the better value when the total is under 50% of replacement cost.
• What failed: Pumps, valves, hoses, filters, and latches are usually practical repairs.
• Tub/inner door panel condition: Rust-through leaks on stainless tub or inner door panel have limited warranty coverage.
• Symptoms: Drain, fill, and heat problems often trace to a single replaceable part.

For model-specific warranty details and troubleshooting steps, check the 2214502N020 owner's manual.

Common repairs that are usually “worth it”

These are frequent, straightforward fixes on many Kenmore dishwashers:

• Not draining: replace the dishwasher drain pump W10876537 or clear a kink/plug in the drain path
• Not filling: replace the valve-water W11175771 or correct a supply issue
• Poor drying or no heat: test/replace the element assembly W10518394
• Door won’t latch or won’t start: inspect/replace the dishwasher door latch WPW10653840
• Odors or poor cleaning: clean/replace the dishwasher filter WPW10463906

What the warranty means for your decision

The Kenmore limited warranty typically includes:

Item	Typical coverage	Why it matters
Whole dishwasher	1 year parts and labor (defects)	Repairs early in ownership are often the best value
Stainless tub and inner door panel	Replacement for rust-through leaks (labor after year 1)	A tub-related leak can still be worth repairing

Why it matters

Replacing a dishwasher is a bigger project than most people expect (fit, plumbing, electrical, disposal connection). If your 2214502N020 has a drain, fill, heat, or latch issue, repairing it often restores full performance for far less than replacement.

Last updated: February 2026

Yes. We still carry replacement parts for many Kenmore dishwashers, including model 2214502N020. The key is matching parts by your full model number so you get the correct fit for common repairs like draining issues, poor cleaning, or heating problems; see the 2214502N020 owner's manual for model-specific guidance.

How to make sure you order the right part

• Use the complete model number from the dishwasher’s rating label (match 2214502N020 exactly).
• Identify the symptom first (won’t drain, won’t fill, not drying, door won’t latch).
• Compare the part name and part ID, not just a description.
• If your dishwasher “won’t drain,” check the drain hose routing and kinks before ordering parts.
• If your dishwasher “won’t fill,” confirm the water supply is on and the float moves freely.

Common Kenmore dishwasher parts we stock for this model

These are examples of parts available for Kenmore 2214502N020 that often solve everyday problems:

Symptom	Part that commonly relates	Example part for this model
Dishes not drying, water not heating	Heating circuit	Element assembly W10518394
Water left in tub, poor draining	Drain system	Dishwasher drain pump W10876537
Door won’t close or won’t start	Door switch/latch system	Dishwasher door latch WPW10653840
Poor wash coverage	Spray system	Dishwasher spray arm WPW10491331
Cloudy water, debris on dishes	Filtration	Dishwasher filter WPW10463906

Why it matters

Kenmore dishwashers are built with model-specific components, so ordering by model number prevents leaks, fit issues, and repeat repairs. The manual also includes troubleshooting steps (for example, checking the drain hose for kinks and confirming the cycle is complete before assuming a drain failure).

Quick troubleshooting before you buy parts

• Won’t drain: confirm the cycle finished, check disposer knockout plug (if connected), and inspect for drain hose kinks.
• Won’t fill: verify the water supply valve is open and the float is not stuck.
• Suds/foam present: switch to dishwasher detergent only; excess suds can stop filling.

Last updated: February 2026

On Kenmore dishwasher model 2214502N020, the model number is printed on the model and serial number label located just inside the door opening, typically along the left side of the tub frame. Open the door fully and look for a rating label with both model and serial information.

Where to look (fast checklist)

• Open the dishwasher door and keep it fully open
• Check the inside edge of the tub frame (not the outer door panel)
• Look along the left-hand side first
• Find a label that lists MODEL and SERIAL
• Write the model number exactly as shown (letters and numbers)

What the label helps you do

Having the correct model number lets us match the right Kenmore parts and diagrams for your dishwasher, including common repair items like the heating element, water inlet valve, and drain pump.

You need	Why it matters	Example from your unit
Model number	Ensures exact part fit and correct diagrams	2214502N020
Serial number	Helps identify production details for service	Printed on same label

Tips to avoid common mix-ups

• Use the full model number, not just the first few characters
• Don’t use numbers from the control panel or cycle names
• If the label is hard to read, take a clear photo with the door open and good lighting

Why it matters

Kenmore dishwashers often share similar-looking doors and racks across series, but internal parts (like the element assembly W10518394 or valve-water W11175771) can vary by model. Using the exact model number prevents ordering the wrong part.

For additional diagrams and label location details, use the 2214502N020 owner’s manual.

Last updated: February 2026

On Kenmore dishwasher model 2214502N020, error code F2E2 means the user interface (console) is not communicating correctly with the main electronic control. This is typically caused by a loose wiring connection, moisture/corrosion at a connector, or a failed console or control board.

What to do first (safe, quick checks)

• Press CANCEL/DRAIN (if available) and let the dishwasher stop.
• Turn power off at the breaker for 1 minute, then restore power.
• Make sure the door is fully latched; a weak latch can interrupt control signals.
• If the code returns, check for stuck keys on the console (a key that feels jammed or won’t click).
• If you recently had a spill or heavy steam, let the unit dry out (door cracked open) and retry.

Likely causes and the most common fixes

What’s happening	Most common cause	Typical fix
F2E2 appears and buttons don’t respond	Console/user interface problem	Inspect console connections; replace console if needed
F2E2 appears intermittently	Loose harness connection	Reseat connectors between console and control
F2E2 appears after a power event	Control logic glitch	Hard reset at breaker; if recurring, replace failed control

Parts that are often involved

If basic resets do not help, the repair usually involves the console or the main control, but a door latch issue can also contribute to “no response” symptoms.

• Owner's manual (use the troubleshooting section to match symptoms and confirm reset steps)
• Dishwasher door latch WPW10653840 (helps ensure the door switch signal is solid during operation)
• Control, electronic W11456660 (main control board that communicates with the user interface)

Why it matters

When the console and main control can’t “talk,” the dishwasher may not start, may stop mid-cycle, or may not respond to button presses. Fixing the communication path restores normal cycle selection, heating, and draining behavior.

Last updated: February 2026

In a Kenmore dishwasher like model 2214502N020, the most commonly replaced parts are the wash and drain components (spray arm, pumps, hoses, filters), the fill and heat components (water inlet valve, heating element), and the door components (latch). These parts wear, clog, or leak over time.

Commonly replaced parts (and what they do)

• Spray arm: spins and distributes wash water; clogs cause poor cleaning.
• Filters: trap food soil to protect the pump; buildup reduces performance.
• Drain pump and drain hose: remove water; failures leave water in the tub.
• Water inlet valve: controls filling; problems can cause no-fill or slow-fill.
• Heating element: heats water and supports drying; failures cause poor drying.
• Door latch: confirms the door is closed so the cycle can run.

Model 2214502N020 parts we see replaced often

Symptom	Likely part to check	Example part for this model
Dishes not getting clean	Clogged or damaged spray arm, dirty filter	Dishwasher spray arm WPW10491331, dishwasher filter WPW10463906
Water left in tub	Drain restriction, weak drain pump, kinked hose	Dishwasher drain pump W10876537, dishwasher drain hose 8269144A
Won’t fill or fills slowly	Water supply issue or inlet valve problem	Valve-water W11175771
Poor drying or not heating	Heating circuit issue or failed heater	Element assembly W10518394
Won’t start or stops mid-cycle	Door not latching or latch switch issue	Dishwasher door latch WPW10653840

Quick checks that prevent repeat failures

• Clean the filter regularly; your manual notes the filtration system needs maintenance to sustain peak cleaning performance.
• Check spray arm holes for debris and clear them.
• Confirm the drain hose is not kinked and the disposer knockout plug is removed (if connected).
• Use rinse aid for better drying results.
• Load so tall items do not block the detergent dispenser.

Why it matters

Replacing the correct part first saves time and prevents secondary issues, such as a clogged filter overworking the pump or a restricted drain causing standing water and odor.

For diagrams, maintenance steps, and troubleshooting guidance specific to Kenmore 2214502N020, use the 2214502N020 owner's manual.

Last updated: February 2026