Kenmore 11027872600 washer Parts

Kenmore model numbers (including 11027872600) are read left to right: the first 3 digits identify the manufacturer, the next group identifies the base design, and the remaining digits narrow down the exact version so you get the correct parts and service information for your washer.

What each section of the model number means

Most Kenmore model numbers follow this pattern:

• Prefix (first 3 digits): manufacturer code (who built the washer for Kenmore)
• Middle digits: the base model or platform (the core design family)
• Ending digits: specific variations (features, revisions, color packages, production changes)

For example:

Model number section	Example from 11027872600	What it tells you
Manufacturer prefix	110	Who built the washer
Base model/platform	27872	The design family
Version/variation	600	The exact variation/revision

Where to find the model number on the washer

On most Kenmore top-load washers, the model tag is commonly found in one of these places:

• Under the lid near the tub opening
• On the rim of the washer cabinet
• On the back of the control console
• On the rear panel of the washer

Why it matters for parts and troubleshooting

Using the full model number helps us match parts that changed over time, even when the washer looks the same. It also helps when diagnosing common issues like no drain, no spin, or no agitation.

• Correct parts fit the first time (less returns and downtime)
• Wiring and switch styles can vary by revision
• Service procedures can differ between versions

Helpful next step

Use the model number exactly as printed on the tag when checking diagrams and procedures in the 11027872600 owner’s manual.

Last updated: January 2026

A Kenmore washer typically lasts 10 to 15 years; for the Kenmore 11027872600, lifespan depends most on load size, installation, and routine maintenance like keeping the drain system clear and avoiding chronic out-of-balance loads. For model-specific care and use details, follow the 11027872600 owner's manual.

Typical lifespan by washer style

Most Kenmore washers fall into these ranges:

Washer type	Typical lifespan	What usually ends it first
Top-load (direct-drive style)	12 to 15 years	Coupler, clutch, lid switch, pump
Front-load	10 to 12 years	Bearings, door boot leaks, drain issues

What helps your 11027872600 reach the high end

We see the longest life when these basics are consistent:

• Keep loads balanced; avoid washing one heavy item by itself.
• Use the correct water level and detergent amount to reduce residue and strain.
• Check pockets; coins and small items commonly damage the pump.
• Level the washer and keep it stable to reduce vibration wear.
• Address slow draining quickly to prevent motor and drive stress.

Parts that commonly affect longevity

If performance drops, these are frequent wear items on many Kenmore top-load designs:

• Coupling 285753A (drive connection between motor and transmission)
• Washer drain pump WP3363394 (drains water; clogs and leaks shorten life)
• Washer lid switch assembly WP8318084 (prevents spin with lid open; failures stop cycles)
• Clutch 285785 (helps the basket reach spin speed; wear causes weak or noisy spin)

Why it matters

A washer that is vibrating, not draining well, or struggling to spin wears out the drive system faster and can turn a small, inexpensive fix into a larger repair.

Last updated: January 2026

To hard reset your Kenmore washer model 11027872600, we recommend disconnecting power for 2 minutes, then restoring power and running a quick test cycle. This clears many temporary control glitches and gets the washer back to normal operation.

Hard reset steps (power reset)

• Turn the washer OFF.
• Unplug the power cord (or switch the breaker OFF).
• Wait 2 minutes.
• Restore power.
• Set a normal cycle and press Start to confirm the controls respond.

If the washer still will not start

These checks fix the most common “looks dead” or “won’t run” symptoms after a reset:

• Confirm the outlet has power (try a lamp or phone charger).
• Make sure the lid closes fully and latches.
• Verify the water faucets are fully open.
• Check that the drain hose is not shoved too far down the standpipe (can cause siphoning and odd behavior).
• If the washer fills but will not agitate or spin, inspect the drive system.

If the lid is not being detected, a failed lid switch can stop agitation and spin; the correct replacement for this model is the washer lid switch assembly WP8318084.

What “hard reset” can and cannot fix

Symptom	Hard reset helps most when	Likely next step if it returns
Random stopping, odd lights, cycle confusion	Control logic is “stuck” after a power event	Check lid switch, timer/controls, wiring
Won’t spin or agitate but motor hums	Temporary control issue or load imbalance	Check coupling 285753A and clutch
Won’t drain	Control glitch after a pause	Check drain hose and pump

Why it matters

A hard reset is the fastest safe first step because it rules out a temporary control-board lockup before you spend time on deeper troubleshooting or parts like a coupling, clutch, or drain pump.

For model-specific operating steps and cycle behavior, use the 11027872600 owner’s manual.

Last updated: January 2026

On the Kenmore 11027872600 (Elite Oasis HE) washer, the UL code indicates an unbalanced load condition that the washer could not correct during the spin cycle. It is most often caused by load size, load distribution, or excess mechanical friction that prevents the basket from spinning smoothly.

What to do first (quick fixes)

• Pause the cycle and redistribute items evenly around the basket.
• Remove a few items if the load is too large or waterlogged.
• Run a Drain/Spin cycle after rebalancing.
• Verify the washer is level and all feet are firmly on the floor.
• Avoid washing a single heavy item (like one blanket) by itself; add a few towels to balance.

When UL points to a mechanical problem

If UL returns with properly loaded, balanced loads, the issue is usually drag or slipping in the drive system. Common causes on this style of Kenmore top-load washer include:

• Worn clutch that cannot bring the basket up to speed
• Worn motor coupling that slips under load
• Basket or drive components binding from wear or corrosion
• Drain problems that leave water in the tub (a heavy, water-filled load goes out of balance easily)

Parts that commonly relate to UL symptoms

Symptom you notice	What it often points to	Example part for this model
Basket struggles to reach full spin	Slipping drive	Clutch 285785
Agitation or spin is weak/intermittent	Drive connection slipping	Coupling 285753A
Washer drains slowly or not fully	Drain restriction or weak pump	Washer drain pump WP3363394

Why it matters

A repeated UL condition is more than an annoyance; it can prevent proper water extraction, leave clothes wetter than normal, and increase wear on the clutch, drive components, and suspension over time.

Helpful reference

For cycle behavior, leveling guidance, and load recommendations specific to Kenmore 11027872600, use the 11027872600 owner's manual.

Last updated: January 2026