Kenmore Elite 79574022411 refrigerator Parts

To raise a Kenmore Elite 79574022411 refrigerator, we adjust the two front leveling legs: turn the legs to the left to raise the cabinet and to the right to lower it. After raising, we re-check level and door closing per the 79574022411 use & care manual.

How to raise and level it (model-specific)

1. Unload heavy items from the doors to reduce weight.
2. With a helper, gently tip the refrigerator back slightly to take weight off the front legs.
3. Turn each front leveling leg:
   • Left (counterclockwise): raises that side
   • Right (clockwise): lowers that side
4. Make small, even adjustments on both sides, then set the unit back down.
5. Open and close both fresh-food doors; if they do not close easily, raise the front slightly more so the cabinet tilts back a bit.

Tools we typically use

• 11/16-inch wrench or flat-blade screwdriver (as specified for this model)
• Work gloves
• A helper (recommended)

If you need more height than the leveling legs allow

On model 79574022411, the manual covers leveling-leg adjustment but does not specify a maximum lift range. If you need a larger raise (for thick flooring transitions or clearance), use a rigid, fully supported platform that does not block airflow.

Good options

• Solid plywood platform with full footprint support
• Appliance-grade riser/base rated for the refrigerator’s weight

Avoid

• Stacking loose shims at corners only
• Soft materials that compress (carpet padding, foam)
• Anything that blocks the front toe-kick area or rear airflow path

Quick checks after raising (prevents problems)

• Confirm the cabinet is stable (no rocking)
• Verify doors seal and self-close normally
• Keep clearance for ventilation (rear and top)
• Re-check water line slack if the unit has an icemaker/dispenser

Check	What you want to see	Why it matters
Side-to-side level	Doors align evenly	Prevents gasket leaks and uneven wear
Slight rearward tilt	Doors close without drifting open	Helps proper door closing
Stability	No wobble	Reduces noise and vibration

Why it matters

Raising and leveling correctly helps the doors seal, keeps the compressor from working harder than necessary, and reduces vibration noise. It also helps prevent water leaks from a strained water line when the refrigerator is moved or re-positioned.

Last updated: January 2026

If the bottom freezer on our Kenmore Elite 79574022411 stopped working, the most common causes are restricted airflow, incorrect control settings (including Demo Mode), or a cooling-system problem such as dirty condenser coils, a failed fan, or frost buildup from a defrost issue. Start with the quick checks in the 79574022411 use & care manual.

Quick checks we recommend first

• Confirm the freezer temperature setting is not set too warm; this model’s freezer control range is -6°F to 8°F.
• Make sure the freezer drawer is closing fully and nothing is holding it open.
• Check that air vents in the freezer are not blocked by packages.
• Look for heavy frost on the back wall inside the freezer (a sign of a defrost problem).
• Verify the refrigerator is not in Demo Mode (Demo Mode disables cooling).

Common causes and what to do

What you notice	Likely cause	What we do next
Freezer is warm and fridge is also warm	Heat not being removed	Clean coils; verify condenser fan runs; check compressor start components
Freezer is warm but you see heavy frost	Defrost system issue	Defrost and test heater and sensor circuits
Freezer temp swings, food softens	Airflow or fan issue	Check evaporator fan operation and air channels

Parts that commonly relate to this symptom (when diagnosis points there)

• Refrigerator condenser coil ACG73645004 if coils are damaged or cannot be cleaned effectively
• Refrigerator condenser fan EAU62025701 if the fan by the compressor is not running
• Refrigerator defrost heater MEE62225112 if the evaporator is iced over from a defrost failure
• Refrigerator defrost sensor assembly 6615JB2005R if the unit is not sensing defrost temperature correctly

Why it matters

A freezer that is not freezing can lead to food spoilage and can make the compressor run longer than normal. Fixing airflow, coil, or defrost problems early helps restore stable temperatures and reduces strain on major components.

Last updated: January 2026

For Kenmore Elite refrigerator model 79574022411, the model and serial number are printed on an identification label inside the fresh food (refrigerator) compartment, on the interior liner. Use the exact model number from that label when ordering parts or checking specifications in the 79574022411 owner's manual.

Where to look (fast checklist)

• Open the refrigerator (upper) door, not the freezer drawer
• Look along the inside walls (the interior liner) of the refrigerator compartment
• Check near the crisper area or side wall where labels are commonly placed
• Find the label that lists both Model No. and Serial No.
• Write the numbers down exactly as shown (including any dots or dashes)

What the label looks like and what to record

Label item	What it’s used for	Example of what to copy
Model number	Correct part fit and diagrams	79574022411
Serial number	Production details and service reference	(varies by unit)
Date of purchase (your records)	Warranty and maintenance tracking	(your date)

Why it matters

Kenmore Elite model numbers can be very similar across series. Using the exact model number from the interior label ensures you get the right refrigerator water filter, air filter, door bin, or ice maker parts that match your specific configuration.

Last updated: March 2026