Craftsman 917377121 gas walk-behind lawn mower Parts

For the Craftsman gas walk-behind lawn mower model 917377121, we recommend using 87-octane (regular) unleaded gasoline for normal operation; higher octane (like 91) does not add power or protection in a small mower engine and is usually unnecessary.

What to use (and what to avoid)

• Use fresh 87-octane unleaded from a busy station.
• Use clean, approved fuel containers to prevent water and dirt contamination.
• Avoid old gas (stale fuel is a top cause of hard starting and rough running).
• Avoid mixing octanes as a “cleaning” method; octane rating is not a cleaner.
• If your area sells ethanol-free gas, it can help reduce storage issues, but 87-octane regular still works well when it is fresh.

Quick comparison: 87 vs 91 in a mower

Fuel choice	What you get	Best use case
87 octane (regular)	Correct performance for most mower engines	Everyday mowing
91 octane (premium)	No added power in typical mower engines	Only if the engine specifically calls for it in the manual

Why it matters

Using the right fuel helps your 917377121 start easier, run smoother, and avoid carburetor varnish and fuel-system deposits that lead to surging, stalling, and no-start problems.

Tips to prevent fuel problems

• Buy only what you will use in 30 days.
• Add fuel stabilizer if the mower will sit more than a few weeks.
• At season end, follow the storage steps in the 917377121 owner's manual.
• If the mower will not start after storage, check ignition and tune-up basics; use our how to keep lawn mower gas from going bad guidance.

Last updated: January 2026

The most common problems we see on the Craftsman 917377121 gas walk-behind lawn mower are drive system issues (won’t self-propel or slips), poor cutting or clumping, and starting or intermittent run problems. Use the diagrams and adjustments in the 917377121 owner's manual to confirm the exact setup for your mower.

Common symptoms and what usually causes them

• Won’t self-propel or drive is weak: worn drive pawls, stretched drive cable, or a slipping pulley/idler setup
• Rear wheels don’t “grab”: worn or sticking drive pawl, missing E-ring, or debris in the wheel drive area
• Cuts unevenly or leaves strips: dull/bent blade, blade adapter wear, deck buildup, or incorrect cutting height
• Clumps or poor bagging: clogged chute, wet grass, damaged deflector, or bag/frame fit issues
• Hard starting or stalls: old fuel, dirty air filter, fouled spark plug, or carburetor varnish (common after storage)

Parts on this model that often relate to those issues

If your symptom matches, these model-specific parts are commonly involved:

Symptom	Parts to inspect on 917377121	What to look for
No/weak self-propel	Lawn mower drive control cable 532197011, drive pawl 532404845	Cable slack, pawl wear, binding
Drive slips/squeals	Lawn mower drive pulley 532443262, husqvarna lawn mower idler pulley 532166043	Wobble, glazing, seized bearing
Poor bagging/discharge	Lawn mower grass bag 583338801, lawn mower clipping deflector 583127101	Tears, gaps, broken hinge/spring
Poor cut quality	Husqvarna lawn mower mulching blade, 21-in 159267, lawn mower blade adapter 532186766	Rounded blade edges, adapter play

Quick checks we recommend before replacing parts

• Drain old fuel and refill with fresh fuel (especially after 30+ days of storage)
• Clean the underside of the deck (built-up grass reduces lift and bagging)
• Verify the drive cable has proper tension and routing per the manual
• Inspect wheels and drive components for packed debris and worn teeth
• Check the blade and blade adapter for looseness or damage

Why it matters

Drive and cutting complaints often come from small wear items (cable, pawls, pulleys, blade adapter). Catching them early prevents belt and transmission strain and restores normal self-propel speed and cut quality.

Last updated: March 2026

The model number for this Craftsman gas walk-behind lawn mower is 917377121. You’ll typically find the model number on the mower’s identification label (often on the rear of the deck, near the handle mounts, or on the engine shroud); the Craftsman 917377121 owner's manual also shows where to look.

Where to find the model number on the mower

Check these common locations on Craftsman walk-behind mowers:

• Rear of the mower deck, near the discharge opening
• Top or side of the deck near the handle bracket
• Under the grass bag door or near the bag frame mounts
• On the engine shroud (engine model may be listed separately)
• Near the wheel height adjuster area

Model number vs. engine model vs. product name

It’s normal to see multiple identifiers. Use the mower model number for parts lookup.

Identifier type	What it identifies	What to use it for
Mower model number (917377121)	The complete Craftsman mower	Ordering correct mower parts
Engine model/type/code	The engine only	Engine-specific parts (carburetor, ignition, etc.)
Marketing name (example: “M210”)	Product line name	General reference, not precise for parts

Why it matters

Using the exact model number 917377121 prevents ordering the wrong parts, especially for drive system items (wheel, pulley, cable), deck hardware, and bagging components that can vary between similar-looking mowers.

Helpful related parts (common identification and service items)

If you’re already servicing or reassembling the mower, these model-matched parts are commonly referenced:

• Molded ignition key 532180331 (for key-start equipped versions)
• Lawn mower drive control lever 532425662 (drive engagement control)
• Lawn mower wheel 532192622 (rear wheel assembly)

Last updated: January 2026