Kenmore Elite 11026944503 washer Parts

For a Kenmore Elite washer model 11026944503, the most reliable “hard reset” is a power reset: unplug the washer (or disconnect power) for about 1 to 2 minutes, then plug it back in. This clears a temporary control or cycle pause and lets you restart the cycle normally; see the owner's manual.

• Turn the cycle control knob to Off (or push the knob in to stop the washer).
• Unplug the washer from the outlet (or switch off the breaker).
• Wait 1 to 2 minutes.
• Plug the washer back in (or turn the breaker back on).
• Close the lid and pull the cycle control knob out to start.
• If the washer was mid-cycle, reselect the cycle and options, then restart.

These checks solve the most common “looks dead” or “won’t run” situations on this style of Kenmore top-load washer:

• Make sure the lid is fully closed; the washer will not agitate or spin with the lid open.
• Check the home electrical supply; reset a tripped breaker or replace a blown fuse.
• Wait through normal cycle pauses; some cycles pause for about 2 minutes.
• Reduce the load size; overloading can stall agitation or spin.
• Confirm the drain hose is installed correctly; the top of the drain hose should be at least 39 in. (99 cm) above the floor (see the installation guide).

A power reset is fast and safe, and it often clears a stalled cycle without replacing parts. If the issue is mechanical (for example, a failed lid switch or drain pump), a reset will not restore normal operation, but it helps confirm the problem is not just a temporary interruption.

Last updated: February 2026

Yes. The Kenmore Elite washer model 11026944503 uses inlet valve screens (small mesh filters) where the hot and cold fill hoses connect to the washer to catch sediment. This model does not use a typical “lint filter” you remove and rinse like some washers.

On model 11026944503, the filtering you can service is at the water inlet connections.

• Turn off both water faucets.
• Remove the hot and cold fill hoses from the washer.
• Check the inlet valve screens for sand, scale, or debris.
• Rinse the screens gently (do not puncture or pry them out).
• Reinstall hoses and check for leaks.

For the exact hose connection and setup details, follow the steps in the installation guide.

If you are chasing “filter” symptoms (slow drain, water left in tub, lint on clothes), the issue is usually in the drain path, not a removable filter.

Common checks:

• Make sure the drain hose is not kinked or clogged.
• Confirm the drain hose height is correct (too low can cause siphoning; too high can slow draining).
• Keep an air gap at the standpipe; do not tape-seal the hose.
• Reduce oversudsing; too much detergent can cause poor draining and spin issues.
• If the washer hums but will not drain, inspect the pump for blockage or wear.

If you suspect a failing pump, the correct replacement for this model is the washer drain pump WP3363394.

Keeping the inlet screens clear helps your Kenmore washer fill at the right speed and protects the water inlet valve. Keeping the drain path clear prevents “won’t drain” problems and reduces strain on the pump and drive system.

Last updated: February 2026

Yes. Kenmore Elite model 11026944503 is part of Kenmore’s premium washer lineup; it’s positioned above standard Kenmore models and is built for higher performance and more robust features. For the exact operating features and cycle options on this specific washer, use the owner's manual.

Kenmore Elite typically indicates a step up in build, performance, and feature set compared to base models. On a washer like 11026944503, that usually shows up as:

• More cycle and option flexibility for different fabric types
• Stronger wash action and better load turnover (agitator and drive system performance)
• Higher spin performance for better water extraction
• More serviceable, replaceable mechanical components over the life of the washer

“High end” matters most in how the washer cleans, spins, and holds up under regular use. Use these checkpoints:

• Cleaning performance: consistent agitation and proper fill levels
• Spin performance: reaches full spin without excessive vibration
• Reliability signals: no burning smell, grinding, or repeated no-drain conditions
• Serviceability: common wear parts are replaceable (coupling, pump, lid switch)
• Fit for your household: handles your typical load size and soil level without re-washing

If the washer is not agitating, not spinning correctly, or not draining, these parts are frequent causes on many Kenmore 110-style top-load designs:

If you are deciding whether to repair or keep this washer, “Elite” usually means it’s worth maintaining when the tub and transmission area are in good shape. Replacing a few common parts can restore performance and extend service life.

Last updated: February 2026

Yes, repairing a Kenmore Elite washer like model 11026944503 is worth it when the problem is a common wear item (lid switch, drain pump, coupling, agitator parts) and the machine is otherwise in good shape; these repairs typically restore normal washing and spinning without the cost of replacement.

Use these practical checkpoints before you buy parts or schedule service:

• Repair if the washer fills, drains, and spins sometimes, but has a single clear symptom (no drain, no spin, won’t start, loud agitation).
• Repair if the fix is a common mechanical part such as a coupling, lid switch, pump, or agitator dogs.
• Replace if you have repeated major failures (gear case, basket drive issues, chronic leaks into the tub bearing area).
• Replace if the total repair cost is near half the cost of a comparable new washer.
• Repair if the cabinet and tub are solid (no severe rust, no major structural damage).

These are frequent fixes on Kenmore top-load designs and are often worth doing first:

• No spin or intermittent spin: check the washer lid switch assembly WP8318084
• Won’t agitate or makes a ratcheting sound: replace agitator dog 80040
• Motor runs but washer won’t move/agitate/spin: inspect washer motor coupling 285753A
• Won’t drain or leaves water in tub: check washer drain pump WP3363394

A targeted repair can extend the life of your washer and prevent secondary damage. For example, running overloaded or unbalanced loads can strain the drive and suspension; the owner's manual guidance on balanced loading and proper additive use helps reduce repeat failures.

• Confirm the symptom (no drain, no spin, leak, noise) and when it happens in the cycle.
• Check for simple causes: overloaded tub, unbalanced load, kinked drain hose, loose power connection.
• Review operating and care tips in the owner's manual to avoid fabric damage and reduce wear.

Last updated: February 2026

Your Kenmore Elite washer model 11026944503 has a 3.2 cu. ft. tub capacity. Use that capacity when comparing replacement washers, planning load sizes, and estimating how bulky items (comforters, towels) will move during wash and spin.

The most reliable place to verify capacity for model 11026944503 is the model-specific documentation.

• Check the Specifications section in the 11026944503 owner's manual
• If you are measuring for a replacement, also review clearances in the 11026944503 installation guide
• Match capacity along with hookup requirements (water pressure, drain setup)

A washer’s cubic-foot rating directly affects load size, cleaning action, and spin performance. Using the correct 3.2 cu. ft. capacity for Kenmore 11026944503 helps you avoid choosing a replacement that feels noticeably smaller or larger in everyday use.

Last updated: February 2026