Kenmore Elite 25324092102 freezer Parts

For Kenmore model 25324092102, the most accurate way to get cubic feet is to look up the capacity in the specifications section of the 25324092102 owner's manual or on the model and serial number plate inside the cabinet. Model numbers alone do not reliably encode capacity across Kenmore product lines.

• Check the specifications/capacity listing in the 25324092102 owner's manual.
• Locate the model and serial number plate; on upright models it is typically on the upper left wall inside the freezer.
• If you still need confirmation, measure the interior and calculate an approximate volume (useful for estimating, not for ordering parts).
• Use the full model number (all digits) when searching for specs; small digit changes can indicate a different cabinet size.

The owner’s guide for Kenmore Elite upright freezers notes the serial plate is located on the upper left wall inside the freezer for upright models.

If you cannot access published specs, you can estimate interior capacity.

Formula: (H × W × D in inches) ÷ 1,728 = cubic feet.

Cubic feet helps you compare storage space and plan food storage, but it is not the best identifier for repair parts. For parts like a door seal, controls, or sealed system components, the exact model number (25324092102) is what ensures fit.

Last updated: February 2026

Most Kenmore Elite refrigerators last 10 to 15 years with normal household use and basic maintenance. For your Kenmore Elite model 25324092102, following the care and operating steps in the 25324092102 owner's manual helps you get the longest, most reliable service life.

Refrigerators and freezers tend to wear based on compressor run time, door openings, and how well the sealed system stays clean and ventilated.

• Average range: 10 to 15 years
• Common “good run” with solid upkeep: 12 to 16 years
• Often replaced earlier when: repairs involve the sealed refrigeration system or major electrical controls

These habits reduce compressor strain, prevent frost problems, and help temperatures stay stable.

• Keep the unit where room temperature stays within normal indoor ranges (avoid hot garages when possible).
• Maintain good airflow around the cabinet so the refrigeration system can reject heat efficiently.
• Keep the door fully closed; fix poor sealing quickly (a leaking gasket forces longer run times).
• Defrost and clear ice buildup if airflow is restricted.
• Use correct power: plug into a properly grounded outlet (avoid extension cords and adapter plugs).

A Kenmore Elite refrigerator or freezer can often reach the upper end of its lifespan when it runs efficiently. Simple items like airflow and door sealing reduce wear on high-cost components like the compressor.

Last updated: February 2026

On the Kenmore Elite upright freezer model 25324092102, the model and serial number plate is typically on the upper left wall inside the freezer compartment. This is the primary location listed in the 25324092102 owner's manual.

• Upper left interior wall inside the freezer (most common for upright models)
• Side wall inside the cabinet near the front opening
• Ceiling area inside the freezer (some uprights place the label here)
• Behind the lower kick plate or front grille area
• Back exterior panel (less common, but worth a quick look)

The plate usually includes both identifiers. We recommend recording both so you can match parts and diagrams correctly.

• Use a flashlight and look for a silver or white sticker/plate.
• Check the upper left interior wall before removing shelves or baskets.
• If frost buildup blocks the label, do a brief manual defrost so the sticker is readable.
• Write the numbers exactly as shown (including any leading digits).

Kenmore upright freezers can look similar across multiple model numbers. Using the exact model number (like 25324092102) helps us match the right parts the first time, including items such as the freezer door gasket 5304507199 if you ever need a seal replacement.

Last updated: February 2026

If your Kenmore Elite upright freezer 25324092102 is running but not freezing, the most common causes are poor airflow around the cabinet, a door that is not sealing, or a cooling/defrost system problem (evaporator fan, defrost heater, thermostat, control board, or compressor). Use the 25324092102 owner's manual to confirm control settings and installation requirements.

• Make sure the temperature control is set colder and give it 24 hours to stabilize.
• Confirm the freezer is plugged directly into a grounded outlet (no extension cord).
• Verify the room temperature is not extreme; this model is intended for locations up to about 110°F.
• Check that the freezer is level so the door closes and seals correctly.
• Look for heavy frost on the back interior panel (a strong clue of a defrost problem).
• Make sure there is space around the cabinet for air circulation.

These are model-matched parts we often see involved in no-freeze complaints:

• Freezer door gasket 5304507199 if the door is not sealing and warm air is leaking in
• Motor 297309000 (evaporator fan motor) if airflow over the evaporator is weak or stopped
• Blade 5308000010 if the fan blade is cracked, loose, or rubbing ice
• Freezer defrost heater 216730700 if frost is blocking airflow through the evaporator
• Thermostat 297216600 (defrost bi-metal thermostat) if the heater is not being energized during defrost

A freezer that is not level, not sealing, or not getting enough air circulation can mimic a major failure. Fixing airflow and door sealing first prevents repeat icing, protects food, and helps the compressor avoid nonstop run time.

Last updated: February 2026

Water on the floor around your Kenmore Elite upright freezer model 25324092102 is typically defrost water that is not draining out through the drain tube, or moisture from warm, humid air leaking past the door seal. Clearing the drain path and correcting door sealing stops most leaks.

During defrosting, this model uses an interior drain plug and an external drain tube under the base area. Follow the locations and access steps in the 25324092102 owner's manual.

• Unplug the freezer before defrost or drain work.
• Pull the interior drain plug straight out from the freezer floor.
• Remove the base panel (if equipped) to access the external drain tube.
• Place a shallow pan under the drain tube; monitor it so it does not overflow.
• Melt ice in the drain opening using small amounts of warm water.
• Reinstall the drain plug when finished; leaving it open lets warm air enter.

If the tube is cracked, loose, or missing, replace the freezer drain tube 5304512272.

If the cabinet is not level, the door can sit crooked and leak humid air, which turns into condensation and water.

• Confirm all bottom corners rest firmly on a solid floor.
• Adjust the front leveling feet so the door closes easily when left halfway open.
• Make sure the cabinet is not touching the wall.

A damaged gasket lets humid air in, causing frost and water.

• Look for tears, hardened sections, or spots not contacting the cabinet.
• Clean the gasket and mating surface with mild detergent and warm water; dry fully.
• Replace a damaged seal with the freezer door gasket 5304507199.

Stopping leaks prevents slippery floors, excess frost buildup, and temperature swings that can affect food storage.

Last updated: February 2026