Kenmore 25370423416 refrigerator Parts

For Kenmore refrigerator model 25370423416, the most reliable way to get cubic feet is to look up the capacity in the specifications section of the owner's manual. If you do not see capacity listed, you can calculate it from the interior measurements (refrigerator and freezer compartments) and convert cubic inches to cubic feet.

Use the owner's manual for model 25370423416 and look for a section labeled Specifications, Product data, or Capacity.

If you have a tape measure, measure the usable interior space (not the outside cabinet size).

• Measure width, height, and depth in inches for the fresh food section
• Repeat for the freezer section (if you want total capacity)
• Multiply each section: W x H x D = cubic inches
• Convert: cubic inches ÷ 1728 = cubic feet
• Add sections together for total capacity

• Measure inside wall to inside wall, not shelf-to-shelf
• Measure depth to the inside face of the closed door gasket area, not the door bins
• Subtract obvious unusable areas (large air ducts, big rounded corners) if they skew the number
• Use the largest rectangular “box” you can reasonably fit inside each compartment

Cubic feet affects how much food you can store and helps you compare refrigerator sizes accurately. It also prevents ordering mismatched storage parts (bins, drawers) for the wrong model.

Last updated: February 2026

If your Kenmore refrigerator model 25370423416 is warm and you hear repeated clicking from the back but the compressor never stays running, the compressor start circuit or the compressor itself is failing. First rule out normal conditions like a defrost cycle and airflow issues before condemning the compressor.

We use these steps because the Use & Care Guide notes the refrigerator can stop cooling during an automatic defrost cycle (about 30 minutes), and basic power or control settings can also prevent the compressor from running.

• Confirm the unit is plugged in firmly and the breaker is not tripped.
• Wait 30 to 45 minutes to rule out an automatic defrost cycle.
• Make sure the toe grille is not blocked (airflow is required for proper operation).
• Verify doors are closing and sealing; warm air infiltration can mimic a cooling failure.
• Check that the temperature controls are not set to “Off” or the warmest setting.

For model-specific operating notes and “normal sounds,” use the 25370423416 owner's manual.

These symptoms strongly point to a compressor problem, but they can also be caused by the inverter/controls or a sealed-system restriction.

• Clicking every few minutes (overload cycling) with no steady run
• Humming briefly, then clicking off
• Refrigerator and freezer both warming even though fans run
• Compressor is extremely hot to the touch and shuts off quickly
• No vibration or sound from the compressor at all (with power confirmed)

On this model, compressor-related repairs often involve one of these components:

• Refrigerator compressor 5304475104 (sealed-system component)
• Refrigerator electronic inverter board 5304512686 (drives the compressor on inverter systems)
• Refrigerator power control board 5304504031 (supplies/controls power to loads)

A misdiagnosed compressor can lead to unnecessary cost. Simple issues like a defrost cycle, blocked toe grille airflow, or a control setting can stop cooling temporarily, while true compressor or sealed-system failures require specialized tools and handling.

Last updated: February 2026

Kenmore refrigerator model 25370423416 does not use a single dedicated “reset button” for the whole refrigerator; the most reliable reset is a power reset (unplugging the unit briefly). On this model, the control panel also includes default settings (resets settings) and a water filter reset (after filter changes). See the owner's manual for the exact button functions on your control panel.

• Power reset (best for many glitches): Unplug the refrigerator, wait 5 to 10 minutes, then plug it back in.
• Default settings: Resets user settings (temperature setpoints, display units, tones) back to factory defaults.
• Water filter reset: Press and hold the water filter icon for about 3 seconds after replacing the filter.
• Cooling system off (Power on-off icon): Turns off cooling for cleaning; it does not remove power from the refrigerator.

1. Unplug the refrigerator from the wall outlet.
2. Wait 5 to 10 minutes to let the control board fully discharge.
3. Plug it back in and allow temperatures to stabilize (cooling recovery can take several hours).

Use the Power on-off icon on the control panel (press and hold about 3 seconds) to turn cooling back on.

Using the right reset prevents unnecessary parts replacement and helps you separate a simple control glitch from a real failure (like a temperature sensor, user interface, or control board issue).

Last updated: February 2026

Kenmore refrigerators typically last 12 to 15 years. With consistent care (good airflow, tight door seals, and clean condenser coils), many units reach the upper end of that range. For model 25370423416, follow the maintenance and operating guidance in the 25370423416 owner's manual.

A refrigerator’s life is mostly driven by heat management and how hard the sealed system has to work.

Big factors that shorten lifespan:

• Dirty condenser coils causing higher compressor run time
• Worn or leaking door gaskets letting warm air in
• Blocked vents or an overpacked freezer reducing airflow
• Frequent door openings and warm food loads
• Poor leveling causing doors to not close consistently

We recommend these habits for Kenmore refrigerators like 25370423416:

• Clean condenser coils regularly (more often with pets or dusty floors)
• Keep the toe grille area clear for proper air circulation
• Confirm doors and the freezer drawer seal tightly all the way around
• Set stable temps (about 37°F fresh food, 0°F freezer)
• Replace odor and water filtration parts on schedule when equipped

If cooling, odors, or sealing issues show up, these model-compatible parts are often involved:

Most “early failures” are really efficiency and cooling-stress problems. When airflow is restricted or seals leak, the compressor and fans run longer, which accelerates wear and increases temperature swings that can spoil food.

Last updated: February 2026