Kenmore 3627391993 gas range Parts

A Kenmore gas range like model 3627391993 typically lasts 15 years with normal household use and basic maintenance. Keeping burners clean, ensuring steady ignition, and addressing weak heating early helps you reach that lifespan.

Most gas ranges reach their full service life when the oven burner lights reliably and the gas flow stays consistent.

• Heavy daily cooking can shorten lifespan
• Poor ventilation and grease buildup can increase wear
• Repeated ignition failures strain components
• Skipping cleaning can cause uneven flames and hot spots
• Promptly replacing worn parts helps prevent bigger failures

These steps help a Kenmore gas stove run cleaner and reduce stress on the ignition and burner system.

• Clean surface burner ports and caps so flames stay even
• Keep the oven bottom and burner area free of spills and soot
• Replace a slow-to-glow oven igniter before it stops lighting
• Use the correct appliance light bulb wattage to avoid heat damage in the socket
• Verify the range is level so cookware heats evenly

A gas range can often run well past a decade, but ignition and gas-delivery problems can turn into no-heat situations. Replacing a failing igniter early is one of the most cost-effective ways to keep your 3627391993 cooking reliably.

Last updated: February 2026

To change a spark electrode igniter on your Kenmore gas range model 3627391993, we shut off power and gas, remove the burner parts to access the electrode, transfer the wire to the new electrode, then reassemble and test for reliable sparking and ignition.

• Turn off power to the range at the breaker (spark ignition uses electricity).
• Shut off the gas supply valve.
• Let all burners cool completely.
• Work in a well-ventilated area.
• If you smell gas at any point, stop and ventilate the area before continuing.

1. Remove the burner grate and burner cap.
2. Lift off the burner head/base so you can see the electrode tip and mounting.
3. Remove the mounting screw holding the electrode to the burner or orifice holder.
4. Pull the electrode up enough to access the wire connector.
5. Transfer the wire to the new electrode:
   • If it uses a push-on terminal, pull the connector straight off and push it onto the new electrode.
   • If it uses a crimp connector, crimp the new connector securely to the wire, then attach it to the new electrode.
6. Reinstall the electrode into the holder and secure it with the screw.
7. Reinstall the burner head/base, cap, and grate.
8. Restore gas and power; test ignition.

• Electrode tip is not aligned near the burner port (gap is off).
• Burner head/base is not seated flat.
• Moisture or food residue is grounding the spark.
• Wire is damaged or not fully seated on the electrode.
• Ignition system issue (switch harness/module) beyond the electrode.

A properly mounted, correctly gapped electrode creates a strong spark at the right spot. That prevents delayed ignition, reduces clicking time, and helps the burner light quickly and evenly.

Last updated: February 2026

To remove the cooktop (top) on a Kenmore gas range model 3627391993, we typically lift the top after removing the grates and burner pieces, then releasing any hidden front or burner-base screws that lock the top down. The exact fastener locations vary by revision, so work slowly and keep screws organized.

• Turn all burner knobs to OFF and let the range cool completely.
• Shut off the gas supply valve.
• Unplug the range (or switch off the breaker) because the igniters and oven light use electricity.
• Protect the countertop and enamel with a towel or cardboard.
• Take a quick photo of each burner area before disassembly.

1. Remove the surface grates.
2. Lift off burner caps.
3. If your model uses removable burner bases, remove the burner-base screws (often in the center of the base).
4. Look for screws along the front lip under the cooktop edge (sometimes accessible when the oven door is open).
5. Lift the cooktop from the front and prop it up (some ranges use support rods; others hinge upward).

• Check for one missed screw near a burner base or the front corners.
• Make sure the burner bases are not stuck to spills; gently wiggle, do not pry hard.
• If an igniter wire feels tight, stop and reposition the top to avoid pulling connectors.

Removing the top correctly prevents stripped screws, cracked burner bases, and damaged igniter wiring. That protects reliable ignition and helps avoid gas odor issues caused by misaligned burner parts.

Last updated: February 2026

Your Kenmore gas range model number is printed on a rating label attached to the appliance. For Kenmore model 3627391993, the label is most often found around the oven door frame (door jamb) or on the frame behind the storage or broiler drawer.

Check these common label locations first:

• Oven door jamb (open the oven door and look along the frame)
• Frame behind the bottom storage drawer or broiler drawer (pull the drawer out)
• Back panel near the vent area
• Side panel near the lower rear corner
• Under the cooktop edge (less common; only if the top lifts on your design)

The label usually includes a few key identifiers. Use the model number to match parts correctly.

Once you find the model number, match it exactly (all digits) before choosing parts.

• Write the model number down exactly as printed
• Take a clear photo of the label for reference
• If the label is worn, use a flashlight and view from an angle
• Use the model number to confirm fit before ordering items like an igniter or gas valve
• For common “no bake” or “won’t ignite” issues on this model, the igniter WB2X9154 is a frequent replacement part

Kenmore ranges can look similar across many model series, but internal components (igniter style, burner tube, light socket, control valve) vary by model. Using the exact model number prevents mismatched parts and repeat repairs.

Last updated: February 2026

If your Kenmore gas range model 3627391993 is clicking but the oven will not light, the most common cause is a weak or failed oven igniter that is not drawing enough current to open the oven gas valve. Less often, the gas valve, wiring, or burner tube alignment is the issue.

• Confirm the range has power (the igniter needs electricity even though the oven uses gas).
• Set BAKE and watch through the oven bottom openings: the igniter should glow bright.
• If you smell gas but no ignition occurs, stop and ventilate; then continue troubleshooting.
• If the igniter glows dull orange or takes a long time to heat, treat it as weak.
• If the igniter never glows, check the wiring connections and power supply.

In this model, these parts commonly relate to “clicking but not lighting” symptoms:

• Igniter WB2X9154 (oven burner igniter; heats to ignite gas and helps open the gas valve)
• Control valve WB19K14 (oven gas valve; opens to release gas when the igniter draws the correct current)
• Tube burner support WB28K60 (bake burner gas supply tube; can contribute if misaligned or restricted)

A weak igniter can keep the oven from lighting even though you hear clicking, because the oven safety system relies on the igniter heating and drawing the right electrical load before the gas valve opens. Fixing the igniter first solves the majority of “won’t light” oven complaints.

• Unplug the range or shut off power at the breaker before accessing internal wiring.
• Shut off the gas supply valve before removing burner or valve components.
• If you ever smell strong gas, stop and ventilate the area before continuing.

Last updated: February 2026