Kenmore Elite 79075233312 gas range Parts

No. The Kenmore Elite gas range model 79075233312 does not use a single dedicated “reset” button; when the controls act up, the standard reset is a power reset (turning the range off at the breaker briefly, then restoring power) and then re-setting the clock and any cooking settings per the 79075233312 owner's manual.

How to reset (power reset) safely

• Turn the range OFF.
• Switch the range circuit breaker OFF (or unplug if accessible).
• Wait 2 to 5 minutes.
• Restore power.
• Re-set the clock and test Bake and a surface burner.

What a reset can and cannot fix

A power reset clears many temporary control glitches, but it will not correct a failed heating or ignition component.

Symptom after reset	Most likely area to check	Common next step
Oven will not heat, no ignition	Ignition system	Inspect/replace the tappan range oven burner igniter 316489403 if it is weak or not glowing properly
Oven heats but temperature is off	Temperature sensing	Test/replace the frigidaire range oven temperature sensor 316490000
Broil will not ignite	Broil ignition	Check the frigidaire range broil igniter 5304506545
Surface burner clicks but won’t light	Surface ignition or gas flow	Clean burner parts; inspect igniter wiring and burner head

Why it matters

On a gas range like the Kenmore Elite 79075233312, “resetting” is mainly about restoring normal operation to the electronic oven controls. If the oven or broiler still will not ignite after a reset, the issue is usually a weak igniter, a sensor problem, or another ignition or control-related failure.

Last updated: February 2026

A Kenmore gas range like model 79075233312 typically lasts about 15 years with normal household use. Consistent cleaning, correct burner flame adjustment, and quick repair of ignition or heating issues help you reach (and often exceed) that lifespan.

What affects lifespan most

• Cleaning habits: spills and grease buildup can clog burner ports and stress igniters
• Proper flame size: flames that are too high waste fuel and overheat components
• Ventilation: using a vent hood reduces heat and grease accumulation around controls
• Ignition health: weak igniters can cause delayed ignition and longer heat-up times
• Oven temperature accuracy: a drifting sensor can lead to overworking the burner

Quick maintenance checklist (monthly to seasonally)

• Wipe cooktop and burner heads; keep ports clear and dry
• Confirm burner flames are steady and mostly blue; adjust per the 79075233312 use and care guide
• Clean or replace your vent hood filter to reduce grease buildup
• Check oven performance; if baking is inconsistent, consider testing the sensor
• Replace failed oven lights with the correct bulb type (40-watt)

Common “wear” parts for this model

If the range still has good gas flow but struggles to ignite or hold temperature, these parts are frequent fixes:

Symptom	Likely area	Example part for 79075233312
Oven won’t ignite or takes too long	Bake ignition	Tappan range oven burner igniter 316489403
Oven temp swings or is inaccurate	Temperature sensing	Frigidaire range oven temperature sensor 316490000
Broil won’t light	Broil ignition	Frigidaire range broil igniter 5304506545

Why it matters

A gas range that is cleaned and adjusted correctly runs more efficiently, heats more evenly, and puts less strain on ignition and control components. That directly supports a full service life and helps prevent nuisance no-heat or weak-heat problems.

Last updated: February 2026

On the Kenmore Elite gas range model 79075233312, the model number is typically printed on a rating label located around the oven door opening (door jamb) or on the frame behind the storage or warmer drawer. Use the exact model number from that label when ordering parts or checking specifications in the 79075233312 use & care guide.

Most common label locations to check

• Oven door jamb: open the oven door and look along the frame near the gasket
• Behind the bottom drawer: pull the storage or warmer drawer out and look on the frame rails
• Back panel: check near the gas connection area and venting
• Side frame: sometimes on the lower side panel near the front
• Under the cooktop edge: occasionally visible when looking up under the front lip

What to write down (so parts match)

We recommend copying the information exactly as shown on the label.

Label item	What it’s used for	Example format
Model number	Correct parts lookup	79075233312
Serial number	Age and production run	Letters and numbers
Gas type (if listed)	Setup and conversion checks	Natural gas or LP

Quick tips if the label is hard to read

• Wipe gently with a damp cloth; grease can hide digits.
• Use a flashlight and take a close-up photo to zoom in.
• If the label is inside the drawer area, remove the drawer fully for a clear view.

Why it matters

Kenmore Elite ranges often share similar styling across multiple model families (for example, 790.7523*). Using the exact model number from the rating label helps ensure the right igniter, temperature sensor, control overlay, and other range parts fit and function correctly.

Last updated: February 2026

If your Kenmore Elite gas range 79075233312 oven is not igniting, the most common causes are loss of electrical power to the igniter system, a weak or failed oven igniter, or a gas ignition sequence issue (normal ignition takes about 30 to 60 seconds). See the 79075233312 installation guide for ignition and power-failure safety details.

Quick checks we recommend first

• Confirm the range is plugged in and the outlet has power (electric ignition requires power).
• Set Bake to 300°F and watch for the igniter glow; the burner should light within 60 seconds.
• Make sure the oven controls are set correctly and not left in an OFF or canceled state.
• Check that the oven vent area is not blocked; the range needs fresh air for proper combustion.
• If you recently had a power outage, reset all oven controls to OFF, then try again.

What “normal” ignition looks like on this model

The igniter should glow first; once it gets hot enough, the oven gas valve opens and the burner lights.

What you see	What it usually means	What to do next
No glow at all	No power, wiring issue, or failed igniter/control	Verify outlet power; inspect wiring; test igniter circuit
Glows but never lights	Weak igniter or gas valve not opening	Replace the igniter first in most cases
Lights after a long delay	Igniter getting weak	Replace igniter to restore normal light-off time

Parts that commonly fix “won’t ignite”

For model 79075233312, these are frequent repair parts when the oven will not light:

• Tappan range oven burner igniter 316489403 (most common for no-ignite or delayed ignition)
• Gas valve issues can also prevent ignition (less common than an igniter)
• Temperature sensing or control problems can stop heat commands (diagnosis needed)

Why it matters

A weak igniter can prevent the gas valve from opening, so the burner never lights even though the oven is calling for heat. Restoring proper ignition timing improves baking performance and helps prevent repeated failed start attempts.

For operating steps and additional troubleshooting, use the 79075233312 owner’s manual.

Last updated: February 2026