Installation guide
Owner’s manual
Error Codes
How do I reset my Kenmore electric range?
To reset a Kenmore electric range model 91145565094, clear the control first, then fully power-cycle the range. If the display is flashing an F code after a glitch or power failure, pressing CLEAR/OFF and restoring power typically returns the control to normal operation.
- Press CLEAR/OFF once to stop any active bake, broil, or timer function.
- If the control is unresponsive, turn OFF the range circuit breaker (or remove the fuse) for 1 minute.
- Turn the breaker ON again.
- Reset the clock if it is flashing after a power failure.
- Re-enter your cooking settings (any in-progress cooking cycle must be set again).
Your manual’s troubleshooting section recommends this reset sequence for a flashing F followed by a number or letter:
- Press CLEAR/OFF.
- Let the range cool for 1 hour.
- Try starting an oven function again.
If the same F code returns after those steps, the issue is typically in the oven control circuit (control, wiring, or a related safety device). Use the wiring diagram and troubleshooting guidance in the 91145565094 owner's manual.
- Household power: confirm the breaker is fully seated (not half-tripped).
- Terminal block and cord connections: loose or overheated connections can cause intermittent resets.
- Control settings: cancel the timer and any delayed-start settings.
- Oven cooling: after an overheat event, allow time for temperatures to drop before retrying.
| Symptom | What it usually means | Best next step |
|---|---|---|
| Clock flashing | Power interruption | Set the clock and reprogram cooking |
| “F” code flashing | Control detected a fault | CLEAR/OFF, cool 1 hour, retry |
| Dead display | No power or connection issue | Check breaker, then inspect terminal block |
A proper reset clears false faults after a power glitch and helps you confirm whether you have a one-time control hiccup or a repeatable failure that needs a part replacement or service.
Last updated: January 2026
What does F5 mean on a Kenmore oven?
On the Kenmore 91145565094 30" electric drop-in range, an F code (such as F5) means the control detected an oven problem. Start by clearing the code, letting the range cool for 1 hour, then trying the function again; if the code returns, service is needed (record the exact code).
- Press CLEAR/OFF to stop the beeping and clear the display.
- Let the range cool for about 1 hour.
- Try using BAKE or BROIL again.
- If F5 repeats, write down the full code and what you were doing (Bake, Broil, Self-Clean).
- Turn off power at the breaker if the control is acting erratically.
For the exact F-code guidance and control display behavior for this model, use the 91145565094 owner's manual.
Many Kenmore electric ranges use F-codes to flag a problem in the oven temperature sensing or control circuit. Common causes include:
- Loose, corroded, or overheated wire connections
- A failing oven temperature sensor circuit
- A problem in the electronic oven control (clock/control)
- Heat damage after high-temperature cooking or self-clean
| What you notice | What it points to | Best next step |
|---|---|---|
| F5 appears during preheat | Temperature sensing/control issue | Reset, then retry Bake |
| F5 appears during self-clean | High-heat related fault | Cool 1 hour, retry later |
| F5 returns immediately after reset | Persistent control/sensor circuit problem | Schedule service and record code |
An F5 code is the range telling you it cannot reliably control oven temperature or a related safety circuit. Clearing the code and cooling the unit helps confirm whether it was a one-time control glitch or an ongoing electrical issue.
Last updated: January 2026
How do I find the model number on my 91145565094?
On Kenmore range model 91145565094, the model and serial number label is located under the cooktop. Lift the cooktop up and look underneath for the tag; write both numbers down for ordering the correct parts and using the right instructions in the owner's manual.
Use these steps to find the tag quickly:
- Turn the range off and let all surfaces cool.
- Stand at the front of the range and locate the lift-up cooktop seam.
- Lift the cooktop up (it is designed to raise for access).
- Look underneath the cooktop for the model and serial number label.
- Record both numbers exactly as shown (including any dots or dashes).
The label includes two key identifiers.
| Item on label | What it’s used for |
|---|---|
| Model number | Ensures diagrams and replacement parts match your exact range |
| Serial number | Helps identify production details when troubleshooting or matching revisions |
Kenmore ranges often have similar-looking versions with different wiring, surface elements, and oven components. Using the exact model number helps us match the correct diagrams and parts, such as a bake element, terminal block, or surface element control switch.
- Wipe gently with a damp cloth and dry; avoid abrasive cleaners.
- Use a flashlight and take a close-up photo to zoom in.
- Copy characters carefully; common mix-ups include 0 and O, and 1 and I.
Last updated: March 2026
