Installation guide
Error Codes
How do I reset a Maytag gas oven?
To reset a Maytag MGR6775BDS gas freestanding range oven, we recommend doing a simple power reset first (it clears many control glitches). If the control has a reset option, use the cancel/clear key sequence shown in the MGR6775BDS installation guide.
- Turn the oven OFF.
- Unplug the range, or switch OFF the circuit breaker for the range.
- Wait 1 to 5 minutes.
- Restore power.
- Set the clock, then try Bake again.
Some Maytag range controls can be reset from the keypad.
- Press CANCEL/CLEAR once.
- If the display is still frozen, press CANCEL/CLEAR again.
- If your control shows a reset prompt, press START to confirm.
A “reset” will not fix a failed heating or ignition part. On a gas range, these are the most common causes when the oven will not ignite or takes too long to preheat:
- Weak or failed bake igniter (glows but does not open the gas valve)
- Failed broil igniter (some models use broil to assist preheat)
- Temperature sensor problem causing incorrect oven temperature readings
- Control issue or wiring connection problem
| Symptom | Most likely part to check | Example part for MGR6775BDS |
|---|---|---|
| No bake heat, no ignition | Bake igniter | Igniter W11596211 |
| No broil heat | Broil igniter | Range broil igniter WP74007966 |
| Oven temperature inaccurate | Oven temperature sensor | Range oven temperature sensor WP74011433 |
Resetting restores normal operation after a power surge or a stuck control state. If the oven still will not heat after a reset, focusing on the igniter and sensor saves time because those parts directly control gas ignition and temperature regulation.
Last updated: February 2026
Why is my Maytag gas oven not working?
On a Maytag MGR6775BDS gas freestanding range, an oven that will not heat is usually caused by a failed igniter, a temperature sensing problem, or a control issue. Start with safe basics (power and gas supply), then focus on the bake and broil ignition system.
- Confirm the range has power (clock/display on); the oven igniter needs electricity even though it is a gas oven.
- Make sure the gas shutoff valve is fully open.
- Try BAKE and BROIL; if neither lights, the issue is often ignition, power, or control.
- If the oven is in a self-clean or lock state, allow it to cool and reset per the MGR6775BDS installation guide.
- Verify the range is installed with proper ventilation and clearances; blocked airflow can affect operation.
A glow-bar igniter can glow but still be too weak to open the gas valve. Symptoms include long preheat times, no flame, or a faint gas smell with no ignition.
Helpful model-matched parts to consider:
- Igniter W11596211 (bake ignition)
- Range broil igniter WP74007966 (broil ignition)
If the sensor is out of range or its wiring is damaged, the control may prevent normal heating or cause erratic temperatures.
Model-matched options:
A failed electronic control or a burned connection can stop the igniter from receiving power.
- Check for loose/burned connections at the terminal block.
- If the display works but the oven never energizes the igniter, the control can be suspect.
Model-matched options:
| Symptom | Most likely cause | What we recommend |
|---|---|---|
| No glow from igniter in BAKE | Igniter open, wiring, control | Inspect wiring; replace bake igniter if damaged |
| Igniter glows, no flame | Weak igniter | Replace igniter |
| Broil works, bake does not | Bake igniter/circuit | Replace bake igniter |
| Heats but temps are off | Sensor issue | Test/replace sensor |
A properly working igniter and sensor keep gas flow and oven temperature under control. Fixing the root cause restores normal preheat time, stable baking results, and safe ignition.
Last updated: February 2026
Why is my gas oven not getting up to temperature?
If your Maytag MGR6775BDS gas oven heats but never reaches the set temperature, the most common causes are a weak bake igniter, a failing temperature sensor, or airflow and installation issues that disrupt combustion. Start by checking for normal ignition and steady burner flame during preheat.
- Confirm the oven is actually lighting during Bake (you should hear ignition and then see a steady flame).
- Watch for a long preheat with a small, lazy flame; that often points to a weak igniter.
- Make sure strong drafts are not blowing across the range; drafts can affect burner ignition and combustion.
- Verify the range is installed so ventilation air below the range is not obstructed.
- If you are at higher elevation (over about 2,000 ft), gas input may need adjustment for proper performance.
A gas oven can light and still underheat if the ignition system or sensing circuit is weak.
| Symptom | Most likely cause | Common fix |
|---|---|---|
| Very slow preheat, burner flame looks weak | Weak bake igniter | Replace igniter W11596211 |
| Temperature swings widely, food undercooks | Sensor drifting out of range | Replace oven sensor 12001655 |
| Oven heats sometimes, then stops | Control or wiring issue | Inspect connections; test components |
Your installation setup can directly affect heating performance. The installation guidance for this model calls out sealing openings behind/under the range and keeping cooling and ventilation airflow unobstructed below the range. It also warns that strong drafts and certain ventilation setups can create ignition and combustion problems.
- Review clearances, airflow, and placement details in the installation guide.
- Avoid placing the range where floor or wall openings create strong air movement.
- Do not use downdraft ventilation that pulls air downward across gas burners.
- You smell gas, see soot, or the flame is yellow and rolling.
- The oven will not ignite at all.
- You suspect a gas adjustment is needed for high altitude.
Last updated: February 2026
