Samsung RF28HFEDBSR/AA-22 refrigerator Parts

For the Samsung RF28HFEDBSR refrigerator, the overall dimensions are 35 3/4 in. W x 70 in. H x 36 in. D (measured with hinges, handles, and doors). The listed weight is 326 lb. For more measuring notes, use the RF28HFEDBSR manual.

Dimensions (common measurement configurations)

Use the configuration that matches how you are installing the refrigerator (especially if you are removing doors/handles to get through a doorway).

• With hinges, handles, and doors: 35 3/4 in. W x 70 in. H x 36 in. D
• Without hinges and door: 35 3/4 in. W x 68 7/8 in. H x 29 in. D
• With hinge and door, no handle: 35 3/4 in. W x 70 in. H x 33 1/2 in. D

Quick reference table

Measurement setup	Width	Height	Depth
With hinges, handles, and doors	35 3/4 in.	70 in.	36 in.
Without hinges and door	35 3/4 in.	68 7/8 in.	29 in.
With hinge and door, no handle	35 3/4 in.	70 in.	33 1/2 in.

Why it matters

Correct dimensions help prevent installation problems like doors that will not open fully, drawers that hit a wall, or a refrigerator that will not fit through a doorway. Depth changes the most depending on handles and doors, so it is the measurement we recommend double-checking.

Last updated: January 2026

For Samsung refrigerators like model RF28HFEDBSR, the most common service issues we see are cooling problems (fresh food too warm or freezer not freezing), ice maker troubles, and water leaks. In many cases, restricted airflow from frost buildup or a fan/defrost-related problem is the root cause.

Most common symptoms customers notice

• Refrigerator section warms up but freezer seems closer to normal
• Ice maker slows down, jams, or stops producing ice
• Loud fan noise, especially after doors have been closed awhile
• Water pooling under crisper drawers or on the freezer floor
• Temperature swings and food spoiling sooner than expected

Quick checks we recommend first (no parts needed)

Use these steps before you assume a major failure; they solve a lot of “not cooling” calls.

• Confirm the unit is not in demo/cooling-off mode (see RF28HFEDBSR manual)
• Make sure doors seal fully; check for torn gaskets and bins holding doors open
• Set temps to typical targets: 37°F fresh food, 0°F freezer
• Clear blocked vents; do not pack food tightly against rear air returns
• Clean condenser area and verify the condenser fan is running (if equipped)

What usually causes the problem

Cooling complaints typically come from one of these categories.

Problem area	What it affects	Common clue
Frost/defrost issue	Airflow through evaporator	Fan noise, weak airflow, warming fridge
Evaporator fan issue	Circulation to compartments	Warm fridge, noisy or silent fan
Sealed system/compressor issue	Overall cooling capacity	Both sections warm, long run times
Water/ice system issue	Ice maker and leaks	No ice, slow fill, puddles

If you suspect a sealed-system cooling failure on RF28HFEDBSR, the compatible compressor for this model is the refrigerator compressor NC1MV90ALPASH.

Why it matters

Cooling and ice maker problems often start small (restricted airflow, frost buildup, dirty condenser) but can quickly lead to unsafe food temperatures and heavy compressor run time. Catching the cause early helps prevent repeat breakdowns.

Helpful DIY guidance

• Why your Samsung fridge stopped making ice and how to fix it
• Diagnosing refrigerator evaporator fan problems video
• Refrigerator wont cool troubleshooting video defrost system problems

Last updated: January 2026

On Samsung model RF28HFEDBSR, RD typically forces a defrost cycle for the fresh food (refrigerator) evaporator only, while FD typically forces a more complete defrost that includes the freezer side (and may also warm related circuits such as the ice room on some versions). Both are service functions used to melt frost quickly during troubleshooting.

What RD vs FD usually does

Even when the exact on-screen labels can vary by control version, the common meanings are:

• RD (refrigerator defrost): Targets the refrigerator compartment evaporator and its defrost heater circuit.
• FD (force defrost): Runs a broader defrost routine that generally includes the freezer evaporator.
• During forced defrost, the compressor and most fans typically stop so heat can clear ice.
• You may hear sizzling/dripping as frost melts and water moves to the drain pan.
• The display may show a code (RD/FD) while the mode is active.

When to use each mode

Use the mode that matches where the frost problem is happening.

If the problem is mainly in...	Try first	What it helps confirm
Fresh food section (warm fridge, iced rear cover)	RD	Refrigerator evaporator icing or airflow restriction
Freezer section (poor freezing, heavy frost)	FD	Freezer evaporator icing or defrost system issue
Ice maker area (clumping, slow ice)	FD	Ice room or freezer-side frost that affects ice production

Why it matters

Choosing RD vs FD helps us defrost the correct evaporator area faster. That can restore airflow temporarily and also helps narrow the root cause (door sealing, blocked vents, defrost heater/sensor issues, or control problems) before replacing parts.

Helpful references for this model

• For control-panel and operating details, use the RF28HFEDBSR manual.
• If ice production is the symptom that led you to forced defrost, our why your Samsung fridge stopped making ice and how to fix it guide is a good next step.

Last updated: January 2026