Craftsman 917374362 lawn mower Parts

On the Craftsman walk-behind mower model 917374362, the model number is printed on a decal on the rear of the lawn mower housing (the back of the deck). Use the model and serial from that decal when ordering parts or checking specifications in the 917374362 owner's manual.

Check these common spots on a self-propelled Craftsman walk-behind mower:

• Rear of the mower housing (back of the deck); this is the primary location for 917374362
• Near the rear discharge door area (around the back edge of the deck)
• On the deck surface near the engine mounting area (less common)
• On the handle support area (occasionally)

We recommend recording both identifiers from the decal so you can match the correct diagrams and parts list.

• Model number (example format: 917.374362)
• Serial number
• Date of purchase (helpful for your records)

Craftsman walk-behind mowers can look similar across multiple model numbers, but parts like the drive belt, control cable, and blade can differ. Using the exact model number helps ensure you get the right replacement the first time.

Last updated: February 2026

For a Craftsman walk-behind mower, we identify the model by the model number on the mower’s ID label; for your unit, the correct model format is 917.374362 (also shown as 917374362 on parts listings). Use that number to match the right parts list and diagrams in the 917374362 owner's manual.

On walk-behind mowers like model 917374362, the model number is typically printed on a label attached to the mower housing or frame. Check these common spots:

• Rear of the deck near the discharge opening
• Top of the deck near the engine mounting area
• Back of the mower housing near the bagger door
• Handle bracket area (left or right side)
• Frame rail near the wheels

We recommend recording the full ID information from the label, not just “Craftsman 22-inch”:

• Model number (example: 917.374362)
• Product number (if listed)
• Engine model/type/code (often on the engine shroud)
• Serial number (if present)

Craftsman model numbers control the exact fit of key wear parts like the blade, drive belt, and control cables. For example, the parts list for 917374362 includes items such as the zone cable 587326602 and the lawn mower ground drive belt, 3/8 x 35-3/8-in 532421527, which must match your mower’s configuration.

Last updated: February 2026

Many Craftsman mowers labeled 6.75 are identified by the model number on the rear housing decal, not by the engine label. For a Craftsman walk-behind mower like the one covered by our documentation, the model number is 917.374362; confirm yours by matching the decal and the details in the 917.374362 owner's manual.

Look for a decal on the rear of the mower housing (not on the handle or engine shroud). On Craftsman walk-behind mowers, that decal lists the model number and serial number.

• Check the rear housing decal for a 9-digit number starting with 917
• Write down both the model number and serial number
• Use the model number to match diagrams, parts, and maintenance specs
• Do not rely on “6.75” alone; it is a power rating used across multiple models

“6.75” commonly refers to an engine power class used on many Craftsman rotary mowers. The mower model number (for example, 917.374362) is what determines the correct blade, drive belt, and control cables.

Using the correct model number prevents ordering the wrong wear parts and hardware. For example, Craftsman model 917.374362 uses model-specific drive and control components such as the zone cable 587326602 and the lawn mower ground drive belt, 3/8 x 35-3/8-in 532421527.

Last updated: February 2026

Common problems on the Craftsman lawn mower model 917374362 are usually maintenance-related: it may not start (stale fuel, dirty air filter, bad spark plug), lose power from grass buildup under the deck, cut unevenly from a worn or bent blade, or vibrate excessively from a loose blade or damaged blade adapter. See the 917374362 owner's manual troubleshooting chart for symptom-by-symptom fixes.

• Won’t start: dirty air filter, out of fuel, stale fuel, water in fuel, spark plug wire off, bad spark plug, control bar not held down
• Loss of power: cutting too much grass, dirty air filter, grass and debris packed under the mower deck
• Poor or uneven cut: worn or bent blade, uneven wheel height settings, debris under the deck
• Excessive vibration: loose blade, worn or bent blade, broken blade adapter, bent crankshaft
• Hard to push or loss of drive (self-propelled): worn drive belt, drive cable out of adjustment, worn drive components

1. Use fresh gasoline; drain and refill if fuel is old.
2. Inspect and clean the underside of the deck (built-up clippings cause drag and poor cutting).
3. Check the blade for damage and tightness; replace if bent or badly worn.
4. Confirm the control bar is held against the handle while starting.
5. Look for obvious drive wear (belt glazing, slack cable, worn wheel drive parts).

Most “big” mower problems start as small issues like stale fuel, restricted airflow, or grass packed under the deck. Fixing those early helps your Craftsman 917374362 start easier, cut cleaner, and reduces wear on the blade, belt, and drive system.

Last updated: February 2026

A 36-inch stand-on mower typically weighs about 800 lb; most models land in the 750 to 850 lb range depending on engine, deck build, and accessories. Your Craftsman 917374362 is a walk-behind mower, so it weighs much less than a stand-on unit; use the Craftsman 917374362 owner's manual for your mower’s exact specifications.

Most 36-inch stand-on units are built as commercial machines, so weight is fairly consistent.

• Typical operating weight: 750 to 850 lb
• Common published spec: about 800 lb
• Heavier configurations: larger fuel capacity, heavier-duty deck, added accessories
• Transport note: add trailer tie-down gear and any attachments when planning load

Weight directly affects handling and transport planning.

• Trailer and ramp capacity
• Tie-down requirements
• Turf impact on soft ground
• Ease of loading, unloading, and storage

If you are asking because you’re servicing the cutting system, match the blade style and hardware to the mower’s parts list and diagrams.

• Use the correct 22-inch replacement blade for this model
• Replace worn fasteners when the blade is removed
• Inspect the discharge area and deflector for damage

Helpful parts commonly used in blade service:

• Husqvarna lawn mower 22-inch deck 3-in-1 blade 532421825
• Lawn & garden equipment nut 532409149

Last updated: February 2026