Kenmore 25370603416 refrigerator Parts

For Kenmore model 25370603416, the most reliable way to get cubic feet is to look up the capacity in the product specifications section of the 25370603416 owner's manual. If you cannot find it there, you can estimate capacity by measuring the interior and converting cubic inches to cubic feet.

How to find cubic feet using the model number

Kenmore model numbers do not consistently encode exact cubic feet, so we use the model number mainly to pull the correct spec sheet or manual.

• Find the model/serial label inside the fresh food section (often on a side wall, ceiling, or behind a crisper drawer)
• Confirm the full model number matches 25370603416 exactly
• Check the specifications section in the 25370603416 owner's manual
• If you are planning an install, also review the 25370603416 installation guide for space and clearance requirements

How to estimate cubic feet by measuring (works for any refrigerator)

Measure the usable interior of each compartment (do not include door bins if you want a conservative estimate).

• Fresh food compartment: length x width x height (in inches)
• Freezer compartment: length x width x height (in inches)
• Add the two volumes together
• Divide by 1728 (since 12 x 12 x 12 = 1728 cubic inches per cubic foot)

Quick conversion table

What you have	What to do	Result
Inches (L x W x H)	Multiply to get cubic inches	Total cubic inches
Cubic inches	Divide by 1728	Cubic feet (approx.)

Why it matters

Cubic feet helps us match the right refrigerator parts and accessories (like shelves, door bins, and ice maker kits) and helps you confirm fit for cabinetry and airflow clearances during installation.

Last updated: January 2026

In a Kenmore top-mount refrigerator like model 25370603416, the upper section is the freezer compartment. It’s the coldest area of the appliance and is designed to keep foods frozen; on many setups it can also support an ice maker.

What you’ll typically find in the upper (freezer) compartment

• Freezer shelves or bins for frozen food storage
• A freezer door gasket that seals cold air in
• An evaporator area that creates the cold air (behind an interior panel)
• Air passages that send cold air down to the fresh food section
• Optional ice-making components on some configurations

How the freezer affects refrigerator cooling

The freezer is the “cold source” for the whole unit. Cold air is produced in the freezer area and then circulated to the refrigerator section. If airflow is restricted (ice buildup, blocked vents, overpacked shelves), the fresh food section often warms up first.

Symptom	What it often points to	Where to check first
Freezer cold, fridge warm	Airflow problem	Vents and evaporator cover area
Frost or ice buildup in freezer	Defrost system issue	Defrost heater and airflow
Doors not sealing well	Warm air leaks	Door gasket contact all around

Related parts that commonly affect freezer performance

If you’re troubleshooting cooling or frost issues on this model, these parts are often involved:

• Refrigerator defrost heater 242044008 (helps prevent heavy frost on the evaporator)
• Frigidaire refrigerator door gasket (white) 242193206 (helps the freezer door seal properly)
• Refrigerator ice maker 241798231 (if your freezer has an ice maker and it’s not producing)

Why it matters

Knowing the upper section is the freezer compartment helps you diagnose problems faster: most “not cold enough” complaints start with freezer airflow, door sealing, or defrost performance.

For model-specific compartment features and door removal details, use the 25370603416 installation guide.

Last updated: January 2026

On the Kenmore 25370603416 top-mount refrigerator, the most expensive repair is usually a sealed-system job, most often the compressor replacement, because the part cost is high and the labor includes opening and recharging the refrigerant system.

What typically costs the most (and why)

The biggest bills usually come from sealed-system components and the labor required to service them.

• Compressor: high part cost; sealed-system labor is significant
• Refrigerant leak repair: time-consuming diagnosis and sealed-system work
• Evaporator or heat exchanger: expensive parts; sealed-system labor
• Electronic control or user interface: higher-priced electronics (varies by model)
• Door assemblies: large, model-specific parts with higher shipping and handling costs

Common high-cost parts for this model

These examples are available for Kenmore model 25370603416 and show why some repairs add up quickly.

Repair area	Example part for this model	Why it can be expensive
Sealed system	Refrigerator compressor 240550946	High part cost; sealed-system labor and refrigerant handling
Sealed system	Refrigerator evaporator 5303918274	Major cooling component; sealed-system labor
Sealed system	Refrigerator heat exchanger (example listed for this model)	Complex sealed-system repair
Door replacement	Refrigerator or freezer door assembly (color-specific)	Large part; alignment and sealing matter

Lower-cost fixes that can still solve big symptoms

Before assuming a compressor is bad, we recommend checking for common, less expensive causes of poor cooling or frost issues.

• Verify temperature settings; wait 24 hours after changes before adjusting again
• Make sure the toe grille is not blocked; airflow is essential for proper operation
• Confirm the cabinet is level and tilted about 1/4 inch front-to-back so doors close and seal
• Inspect door gaskets for gaps, tears, or warm air leaks
• If you see heavy frost, defrost-system parts can be a more affordable fix (for example, refrigerator defrost heater 242044008)

Why it matters

A compressor diagnosis is often the turning point between repairing and replacing a refrigerator. Ruling out airflow, door sealing, and defrost problems first helps avoid paying for a major sealed-system repair that does not address the real cause.

For model-specific setup and checks (leveling, airflow, and water/ice maker guidance), follow the installation guide.

Last updated: January 2026

Yes. On Kenmore model 25370603416, we can safely replace many common refrigerator parts ourselves (bins, drawers, shelves, and some door seals) with basic tools after unplugging the refrigerator; sealed-system and compressor-related repairs are best left to a technician.

Good DIY replacements vs. pro-level repairs

Many repairs on a top-mount refrigerator are straightforward, but anything involving refrigerant lines or specialized electrical diagnosis should be handled professionally.

Usually DIY-friendly

• Door bins and gallon bins (snap in and out)
• Crisper drawers and covers
• Shelves and shelf supports
• Ice maker replacement if the wiring harness and mounting points are accessible
• Door gasket replacement (if you can fully seat the gasket and confirm a tight seal)

Usually technician-level

• Sealed system work (refrigerant leaks, filter dryer, heat exchanger)
• Compressor replacement
• Complex control or wiring issues that require live-voltage testing

Safety and prep checklist (do this first)

Before we start any repair, we follow these basics.

• Unplug the refrigerator (or switch off the breaker)
• Protect floors; avoid shifting the refrigerator side-to-side to prevent floor damage
• Keep the toe grille area clear; airflow is required for proper operation
• If the refrigerator is connected to water, shut off the water supply and check for leaks after reconnecting
• After changing temperature controls, wait 24 hours before making additional adjustments

Quick part examples for this model

These are common, customer-replaceable parts we see on Kenmore 25370603416.

Repair need	Example part type	Example model-matched part page
No ice or broken ice maker	Ice maker assembly	Refrigerator ice maker 241798231
Drawer cracked or missing	Crisper drawer	Crisper drawer - refrigerator storage component by frigidaire 240337103
Door not sealing well	Door gasket	Frigidaire refrigerator door gasket (white) 242193206

Why it matters

DIY replacement of non-sealed components can restore cooling performance, reduce frost and moisture issues, and prevent food spoilage. Using model-matched parts for 25370603416 also helps ensure proper fit and reliable operation.

For installation clearances, leveling, and water supply requirements (including typical 30 to 100 psi water pressure guidance), follow the 25370603416 installation guide.

Last updated: January 2026