Kenmore 79551313012 refrigerator Parts

Kenmore Elite dimensions depend on the exact model and style (side-by-side, French door, top freezer). For Kenmore model 79551313012 (side-by-side), the most accurate dimensions are listed in the 79551313012 owner's manual; use that spec so you know the refrigerator will fit your cabinet opening and allow proper airflow.

How to get the right dimensions (and measure your space)

• Find the model number on the inside wall of the fresh food compartment (or on the door frame) and match it to 79551313012.
• Use the manual specs for width, height, and depth (depth is often listed with and without handles).
• Measure your opening in three places (top, middle, bottom) and use the smallest measurement.
• Plan clearance for door swing and drawer pull-out, especially on a side-by-side.
• Leave ventilation space around the cabinet so the condenser can reject heat efficiently.

Typical Kenmore Elite refrigerator size ranges (quick reference)

These ranges help you sanity-check your measurements, but the manual is the final word for 79551313012.

Refrigerator style	Typical width	Typical height	Typical depth
Side-by-side	32 to 36 in.	66 to 71 in.	30 to 35 in.
French door	33 to 36 in.	68 to 71 in.	29 to 36 in.
Top freezer	28 to 33 in.	61 to 67 in.	28 to 34 in.

Why it matters

Correct dimensions prevent installation headaches like doors hitting walls, shelves not clearing, or poor cooling from blocked airflow. If your refrigerator runs warm after a tight install, cleaning airflow paths and keeping clearances can help; the 79551313012 owner's manual covers placement guidance.

Last updated: February 2026

Your Kenmore refrigerator’s model number is printed on the appliance’s rating label; once you find it, match it exactly (letters and numbers) to look up the correct parts and diagrams. For this parts page, the model is 79551313012; confirm your label matches that number.

Where to find the model number label

Check these common locations on Kenmore side-by-side refrigerators:

• Inside the fresh food compartment on a side wall (often the right wall)
• On the door frame when you open the refrigerator door
• Behind the lower kick plate or toe grille
• Near the crisper drawers or ceiling area inside the refrigerator section

If the label is dirty or faded, wipe it gently and use a flashlight to read the full number.

How to read the label so you get the right parts

Use these tips so you do not end up with the wrong Kenmore replacement part:

• Copy the entire model number exactly as shown (example: 79551313012)
• Record the serial number too; it helps confirm production details
• Watch for look-alike characters (0 vs O, 1 vs I)
• If there is a revision suffix, include it if shown on the label
• Use the model number (not the brand name) when searching for parts like an ice maker, thermistor, or control board

Quick check: model number vs serial number

Label item	What it does	Why it matters
Model number	Identifies the design family	Ensures parts fit and wiring/connectors match
Serial number	Identifies your specific unit	Helps narrow down version changes

Why it matters

Kenmore refrigerators can look identical across multiple model numbers, but parts like the ice maker assembly, evaporator fan motor, or dispenser components can differ. Matching the model number exactly is the fastest way to get compatible parts and correct repair instructions from the 79551313012 owner's manual.

Last updated: February 2026

For your Kenmore refrigerator model 79551313012, the most reliable way to choose the correct water filter is to match the filter part number listed for your exact model, then confirm it fits your housing style (push-in, twist-in, or inline) using the instructions in the 79551313012 owner's manual.

The fastest ways to identify the right filter

Use these checks in order; they prevent buying a filter that “looks right” but will not seal or flow correctly.

• Confirm your model number: 79551313012 (inside the fresh food compartment, typically on a wall label)
• Check the existing filter for a printed part number (remove it and read the label)
• Compare the filter’s mounting style (twist-lock vs push-button release)
• Verify whether your refrigerator uses an internal cartridge or an inline filter in the water line
• Follow the replacement steps in how to replace the water filter in a Kenmore refrigerator to confirm the style and seating method

What to match (and what not to)

A correct match is about fit and sealing, not just brand.

What to match	Why it matters	Where to find it
Model number (79551313012)	Ensures the filter is designed for your exact Kenmore platform	Rating label inside the refrigerator
Filter part number	Prevents leaks, poor flow, and bypass issues	Printed on the old filter or listed in the manual
Installation style	A different style will not lock in or seal	Filter head/housing and manual instructions
Change interval	Keeps taste and flow consistent	Manual guidance and your water quality

Why it matters

Using the wrong refrigerator water filter can cause slow dispensing, leaking at the filter head, odd-tasting water, or ice maker fill problems. Matching by model number and part number protects the water system and helps the dispenser and ice maker run normally.

Last updated: February 2026

On Kenmore model 79551313012 side-by-side refrigerators, we typically find the model number on the rating label inside the fresh food (refrigerator) compartment, most often along a side wall near the front, or on the ceiling area near the top. The exact spot is shown in the 79551313012 owner's manual.

Most common places to check

Look for a white or silver sticker or plate that lists MODEL and SERIAL.

• Inside the refrigerator section on the left wall near the top shelf
• Inside the refrigerator section on the right wall near the crisper area
• On the ceiling of the refrigerator compartment (near the light housing)
• On the door frame (the vertical frame the door seals against)
• Less commonly, behind the toe grille or on the back exterior panel

What the label looks like and what to write down

The label usually includes both identifiers. Record them exactly as printed.

What to capture	How it’s labeled	Why we need it
Model number	MODEL or Model	Ensures parts fit your exact refrigerator
Serial number	SERIAL or S/N	Helps match production version and revisions

Quick tips to find it faster

• Use a flashlight; the label can be hard to see under shelves.
• Wipe condensation or smudges off the sticker so the characters are readable.
• Take a photo of the label before ordering parts.

Why it matters

Kenmore refrigerators can look identical across multiple model numbers, but parts like the ice maker assembly, control board, or door bins can vary by revision. Using the correct model number helps us match the right replacement part the first time.

Last updated: February 2026

To replace the ice maker in your Kenmore 79551313012 side-by-side refrigerator, we shut off the water supply, unplug power, remove the ice bin and mounting screws, swap the ice maker assembly, then restore water and power and test harvest and fill. Use the 79551313012 owner's manual for the exact access and screw locations.

Before you start (safety and prep)

• Unplug the refrigerator or switch off the breaker.
• Turn off the water supply valve to the refrigerator.
• Empty the ice bin and remove it from the freezer.
• Protect the floor with towels; a small amount of water can spill.
• Use a 1/4-inch nut driver or Phillips screwdriver (varies by bracket).

Replacement steps (typical side-by-side procedure)

1. Remove the ice bin and any shelf or cover blocking the ice maker.
2. Disconnect the ice maker wiring harness (release the locking tab, do not pull wires).
3. Remove the mounting screws and lift the ice maker off the bracket.
4. Transfer any parts that must move over (bail arm, fill cup, mounting bracket) if your replacement does not include them.
5. Install the new ice maker, tighten screws evenly, and reconnect the harness.
6. Turn water back on, plug in power, and allow 12 to 24 hours for normal ice production.

If you are replacing the assembly for this model

Use the correct ice maker assembly for Kenmore 79551313012; a common match on this model page is the lg refrigerator ice maker assembly 5989JA1002D.

Quick checks after installation

• Confirm the freezer is at 0°F (minus 18°C) for reliable ice production.
• Make sure the shutoff arm (if equipped) moves freely.
• Verify the fill tube is not frozen and is aimed into the fill cup.
• Check for leaks at the rear water connection and inside the freezer.

Common symptoms and what they usually mean

Symptom	Most common cause	What we do next
No ice at all	Freezer too warm, no water fill	Set temp, confirm water supply and fill tube
Small or hollow cubes	Low water flow, clogged filter	Replace filter, check inlet valve flow
Ice clumps in bin	Door not sealing, humidity	Inspect gasket and door alignment

Why it matters

A correctly installed ice maker prevents leaks, protects the dispenser area from icing, and helps the freezer maintain stable temperatures for consistent cube size.

Last updated: February 2026

If the ice maker on your Kenmore 79551313012 side-by-side refrigerator isn’t making ice, the most common causes are a shutoff water supply, a frozen fill tube, a clogged filter or low water pressure, or a failed ice maker component. Start with water flow checks, then move to the ice maker and dispenser parts.

Quick checks that fix most “no ice” problems

• Confirm the freezer is cold enough (target is 0°F); ice makers often stop above about 10°F.
• Make sure the ice maker is turned ON and the shutoff arm or sensor isn’t blocked by the ice bin.
• Verify the household water valve is fully open and the supply line isn’t kinked.
• Replace the water filter if it’s overdue, then purge air from the line.
• Look for a frozen fill tube behind the ice maker; thaw it with a hair dryer on low (do not overheat plastics).
• Dump old clumped ice and reseat the bin so the auger and door switch engage correctly.

What to check next (in order)

1. Water supply and pressure: Low pressure can prevent the mold from filling.
2. Fill tube icing: Usually caused by seepage at the inlet valve or warm air leaks.
3. Ice maker assembly: If it never cycles or won’t harvest, the module can fail.
4. Dispenser and bin drive: If cubes are made but won’t dispense, focus on the bin/auger side.

Parts that commonly solve ice maker issues

Symptom	Most likely area	Example part for this model
No ice, mold stays dry	Water delivery issue	Refrigerator water tube fitting 4932JA3002C
Ice maker won’t cycle or harvest	Ice maker assembly	Lg refrigerator ice maker assembly 5989JA1002D
Ice in bin but won’t dispense	Bin/auger drive	Refrigerator auger motor EAU59551204

Why it matters

An ice maker is a small system: temperature, airflow, and water flow all have to be right. Fixing the root cause (like low water pressure or a frozen fill tube) prevents repeat failures and protects parts like the ice maker assembly and auger motor.

Model-specific help

Use the 79551313012 owner’s manual to confirm ice maker ON/OFF operation, control settings, and any diagnostic steps for your exact configuration. For dispenser teardown steps, follow how to disassemble a Kenmore refrigerator dispenser.

Last updated: February 2026

Kenmore model numbers are read left to right; the first 3 digits identify the manufacturer code, and the remaining digits narrow down the exact design and version. For your Kenmore refrigerator model 79551313012, using the full model number is the fastest way to match the correct parts list and diagrams in the 79551313012 owner's manual.

Where to find the model number on a Kenmore refrigerator

Most Kenmore side-by-side refrigerators place the model and serial tag in one of these spots:

• Inside the fresh food compartment on a side wall
• On the ceiling of the fresh food compartment near the light
• Along the door frame (hinge side)
• Behind the lower toe grille or kick plate area
• On the back panel (less common for day-to-day access)

How the number is structured (what each section means)

Kenmore uses a prefix system; the first three digits are the key identifier for who built the unit, and the rest define the platform and revision.

Section of model number	Example from 79551313012	What it tells you
Manufacturer prefix	795	Who manufactured the refrigerator
Series / platform	51313	Design family used for parts matching
Version / variation	012	Engineering revision, color, or feature variation

Why the full model number matters when ordering parts

Even small digit changes can mean different shelves, ice maker parts, or dispenser components. Using the complete 79551313012 model number helps us match the correct assemblies and avoids returns.

Common part-matching areas that vary by version:

• Ice maker and dispenser components (ice bin, chute door, auger drive)
• Water system parts (tubing, fittings, water tank)
• Door hardware (hinges, handles, bins)
• Temperature sensing and airflow parts (thermistors, dampers)

Quick tip for dispenser and ice system identification

If you are troubleshooting ice dispensing or crushed ice issues, the parts list for this model commonly includes items like the refrigerator auger motor EAU59551204. For step-by-step access to the dispenser area, use how to disassemble a Kenmore refrigerator dispenser.

Why it matters

Reading the model number correctly ensures you get parts that physically fit and electrically match your Kenmore refrigerator, especially for ice maker, water dispenser, and control board repairs.

Last updated: February 2026

Most Kenmore refrigerators, including model 79551313012, typically last 10 to 15 years with normal household use. Regular maintenance (airflow, clean coils, good door sealing) and fixing cooling or ice maker issues early are what most often push a refrigerator toward the high end of that range.

Typical lifespan and what affects it

A refrigerator’s life is usually determined by how hard the sealed system and fans have to work to hold temperature.

• Maintenance habits: dirty condenser coils and blocked vents shorten life
• Door seal condition: air leaks force longer run times
• Ice and water system health: leaks and clogs can cause secondary damage
• Room conditions: hot garages and tight enclosures increase compressor load
• Repair timing: replacing a failing fan motor early prevents bigger failures

Quick maintenance checklist (high impact)

Use these steps to extend the service life of a Kenmore side-by-side refrigerator:

• Vacuum and brush condenser coils regularly (more often with pets)
• Keep food from blocking air vents in the freezer and fresh food sections
• Clean and inspect door gaskets; confirm the door closes without resistance
• Replace water filters on schedule and flush the dispenser after changes (see how to replace the water filter in a Kenmore refrigerator)
• Address unusual noises, warm temps, or frost buildup promptly

Common “life-shortening” symptoms and likely areas

Symptom	What it often points to	Example part for this model
Warm freezer or fridge	Airflow or defrost problem	Refrigerator evaporator fan motor 4681JB1029S
Water under or inside fridge	Drain restriction or tube issue	Refrigerator drain tube 5251JA3003D
Ice maker stops or jams	Ice maker or dispenser components	Lg refrigerator ice maker assembly 5989JA1002D

Why it matters

A refrigerator that runs longer to maintain temperature uses more energy and wears out key components faster. Keeping airflow clear and fixing leaks early protects the compressor and helps your Kenmore 79551313012 reach its expected lifespan.

For model-specific care and cleaning guidance, follow the 79551313012 owner's manual.

Last updated: February 2026