Craftsman 113179151 16-gallon wet/dry vacuum Parts

Yes, you can vacuum drywall dust with a shop vac like the Craftsman 113179151 16-gallon wet/dry vacuum, but you need the right filtration and cleanup habits because drywall dust is extremely fine and clogs filters fast. For best results, use a fine-dust filter and a collection method that keeps dust out of the motor airflow.

• Use a fine-dust or HEPA-style cartridge filter made for drywall or fine debris.
• Add a pre-separator (cyclone bucket or dust separator) to catch most dust before it hits the filter.
• Keep the filter clean; tap it out outdoors or use gentle compressed air from the clean side.
• Empty the drum before it gets more than about 1/3 to 1/2 full of dust.
• Use a drywall sanding vacuum attachment or sanding screen setup when possible.

Drywall dust can turn into a paste and harden inside the tank and hose.

• Do not vacuum wet drywall mud or joint compound unless you are set up for wet pickup and immediate cleanup.
• Do not run the vacuum with a clogged filter; suction drops and the motor runs hotter.
• Do not use a standard paper filter bag as your only defense for fine dust.

Drywall dust is one of the fastest ways to lose suction in a wet/dry vacuum. Better filtration and pre-separation protect airflow, reduce mess, and help the motor last longer.

For general DIY safety and best practices before starting, use are diy appliance repairs safe.

Last updated: February 2026

On the Craftsman wet/dry vacuum model 113179151, the model number is typically printed on the rating label (a sticker or plate) on the powerhead or lid area; look for a line that says MOD or Model followed by the number.

Look in these spots first (they are the most common across 16-gallon wet/dry vacuums):

• On the top lid/powerhead, near the handle or switch
• On the underside of the lid/powerhead (lift the motor head off the drum)
• On the back or side of the motor housing near the cord wrap
• On the rear of the drum/canister near the hose port
• Near the casters/wheel area on the lower drum

Most labels include several identifiers. Use the model number for parts lookup, not the serial number.

If the sticker is faded, these steps usually make it readable again:

• Unplug the vacuum before handling the powerhead
• Wipe dust off with a dry microfiber cloth first
• Use mild soap and water on the drum label; avoid soaking the motor head label
• Shine a flashlight across the label at a low angle to highlight faint print
• Take a close-up photo and zoom in to read small characters

Craftsman wet/dry vac parts (filters, hoses, latches, switches, and motor components) vary by model and production run. Using the exact model number helps us match the correct replacement parts the first time.

For more help with identification, use how to find your appliance model number (and what it means for parts).

Last updated: February 2026

On the Craftsman 113179151 16-gallon wet/dry vacuum, the filter typically comes off from under the power head: unplug the vac, remove the lid (motor head), then pull the filter straight off the filter cage or retainer. If it feels stuck, twist gently while pulling to break the dust seal.

• Unplug the vacuum and move it to a well-ventilated area.
• Release the side latches and lift off the power head.
• Locate the filter on the center filter cage.
• Remove any retaining nut, cap, or ring (if your version uses one).
• Pull the filter straight off; twist slightly if it is packed with fine dust.
• Tap debris into a trash bag, or rinse only if your filter type is washable.

Different Craftsman filters remove the same way, but cleaning is different.

• Hold the filter cage with one hand and pull with the other to avoid cracking plastic.
• Work around the base of the filter, pulling evenly instead of yanking one side.
• If it is caked with drywall dust, take it outside first; it releases in clumps.
• Inspect the rubber sealing surface; a stuck seal is the usual reason it feels “glued on.”

A clogged wet/dry vac filter is the most common cause of low suction and overheating. Removing and cleaning the filter regularly helps airflow, protects the motor, and improves pickup performance.

For general DIY safety and best practices before servicing electrical equipment, follow our guidance in are diy appliance repairs safe.

Last updated: February 2026

Some Shop-Vac brand filters can physically fit a Craftsman wet/dry vacuum, but for Craftsman model 113179151 we recommend matching the filter by the Craftsman-compatible filter number and the exact filter style (cartridge, foam sleeve, or fine-dust/HEPA) so you get the correct seal and airflow.

For this 16-gallon Craftsman wet/dry vacuum, common compatible Craftsman filter options include these filter numbers:

• CMXZVBE38751
• CMXZVBE38753
• CMXZVBE38754
• CMXZVBE38773
• CMXZVBE38755
• CMXZVBE38776
• CMXZVBE38777
• CMXZVBE38778
• CMXZVBE38779

Use this quick checklist before buying any “universal” or Shop-Vac labeled filter:

• Match the filter type to the job: dry debris, fine dust, or wet pickup
• Match the mounting method: center hole and nut, band clamp, or slip-on cage
• Match key dimensions: height and inside diameter (ID) to your current filter
• Confirm it clears the float/cage assembly so it seats fully
• Replace the filter if it is torn, oil-soaked, or won’t seal tightly

A filter that does not seal tightly lets fine dust bypass into the motor area; that reduces suction and shortens motor life. Using a Craftsman-matched filter keeps performance consistent and protects the vacuum.

For help confirming the exact model tag before ordering, use how to find your appliance model number (and what it means for parts).

Last updated: February 2026