Kenmore 1069530682 refrigerator Parts

You can find the model number for your Kenmore refrigerator on the appliance’s model and serial tag. On Kenmore side-by-side models like 1069530682, it’s typically inside the fresh food (refrigerator) compartment on a side wall near the crisper drawers, or on the frame behind the lower kickplate (toe grille).

Where to look first (fastest checks)

• Open the refrigerator door and check the inside side walls near the bottom
• Look behind or just above the crisper drawers
• Check the door frame area (hinge side is common)
• Remove the lower kickplate/toe grille and look on the frame behind it
• If the tag is dirty or faded, wipe it gently and use a flashlight at an angle

What the model tag looks like

Most Kenmore refrigerator tags include:

• Model number (example: 1069530682)
• Serial number
• Electrical ratings (volts/amps)
• Sometimes a bar code

Why the model number matters

We use your exact model number to match the correct parts list and diagrams for your refrigerator. That prevents ordering look-alike parts that do not fit, especially for ice maker, water system, and temperature control components.

Common parts that depend on the exact model

System	Example part on this model	What it affects
Ice maker	Ice maker assembly - refrigerator ice maker by whirlpool 4317943	Ice production and harvest
Water supply	Refrigerator inlet valve WP2315576	Water to dispenser and ice maker
Temperature control	Refrigerator thermostat WP2198202	Cooling cycles and cabinet temperature

If you cannot find the tag

• Check for a second label near the kickplate area
• Look for a tag that may be partially hidden by a drawer track or trim
• If the label is missing, use the parts diagrams for 1069530682 to compare assemblies (ice maker, inlet valve, door gasket) and confirm fit

Last updated: February 2026

On Kenmore side-by-side refrigerators like model 1069530682, the model number is printed on the appliance identification label. You will typically find that label inside the fresh food (refrigerator) compartment on a side wall, near the top, or around the door opening.

Common places to check first

Unplugging is not required just to read the label, but keep the doors open only as long as needed.

• Inside the refrigerator section on the left or right interior wall
• On the ceiling of the fresh food compartment (near the light housing)
• On the frame around the refrigerator door opening (door jamb area)
• Behind the crisper drawers (look on the side wall just above the drawer rails)
• On the back exterior panel (less common, but worth a quick check)

What the label looks like and what to write down

The label usually includes both a model number and a serial number. For ordering parts and matching diagrams, we use the model number.

Item on label	What it’s used for	Example format
Model number	Correct parts list and fit	1069530682
Serial number	Production info and dating	Letters and numbers

Why it matters

Kenmore model numbers can look similar across different refrigerator builds. Using the exact model number (for example, 1069530682) helps us match the correct parts for your dispenser, ice maker, defrost system, and door seals.

If you’re trying to order a part after you find the model number

Once you confirm the model number, you can match common repairs to the correct part listing, such as the ice maker assembly - refrigerator ice maker by whirlpool 4317943 or the refrigerator inlet valve WP2315576.

Last updated: February 2026

For your Kenmore side-by-side refrigerator model 1069530682, the most reliable way to confirm cubic feet is to read the capacity on the refrigerator’s rating label inside the fresh food section; if it is missing or unreadable, we calculate capacity by measuring the interior and converting cubic inches to cubic feet.

Fast ways to find the cubic feet

• Check the rating label inside the refrigerator compartment (commonly on a side wall, ceiling area, or near the crisper area); look for “Total volume”, “Capacity”, or “Cu. Ft.”
• Search by model number 1069530682 in our parts and model resources to confirm the exact configuration
• Measure the usable interior space and calculate cubic feet (best when labels are worn)
• If you are troubleshooting cooling or airflow, confirm the evaporator fan is running; poor airflow can make the refrigerator feel “small” because temperatures are uneven (see how to fix your evaporator cooling fan)

How to calculate cubic feet (simple method)

1. Empty the section you are measuring (fresh food and freezer can be measured separately).
2. Measure the interior:
   • Height (inches)
   • Width (inches)
   • Depth (inches)
3. Multiply: Height × Width × Depth = cubic inches
4. Convert: cubic inches ÷ 1,728 = cubic feet

Quick conversion table

What you have	What to do	Result
Interior measurements in inches	Multiply H × W × D	Cubic inches
Cubic inches	Divide by 1,728	Cubic feet
Separate fresh food + freezer volumes	Add both cubic feet values	Total cubic feet

Tips so your measurement matches “real” capacity

• Measure to the inside liner, not the door bins.
• Subtract space taken by fixed features (large light housings, big air towers) if they significantly reduce usable volume.
• Use the same approach for both compartments so your total is consistent.

Why it matters

Knowing cubic feet helps us match the right parts and performance expectations for your Kenmore 1069530682, such as airflow components (like the refrigerator evaporator fan blade WP2169142) and temperature controls.

Last updated: February 2026

To replace the ice maker in your Kenmore 1069530682 side-by-side refrigerator, we shut off the water supply, unplug the refrigerator, remove the old ice maker, then install and reconnect the replacement ice maker so it can cycle and fill normally. Using the correct ice maker assembly prevents leaks and no-ice problems.

What you need before you start

• A replacement ice maker that matches your model (use ice maker assembly - refrigerator ice maker by whirlpool 4317943)
• 1/4-inch nut driver or screwdriver (common for mounting screws)
• Towel or shallow pan (to catch drips)
• Work gloves (sheet metal edges can be sharp)

Step-by-step: replacing the ice maker

1. Turn off the water to the refrigerator (house shutoff valve).
2. Unplug the refrigerator (or switch off the breaker).
3. Remove the ice bin to access the ice maker.
4. Disconnect the wiring harness from the ice maker (release the locking tab if present).
5. Remove mounting screws, then lift the ice maker off the mounting points.
6. Disconnect the fill tube or inlet connection if your setup uses one at the ice maker.
7. Install the new ice maker on the mounting points and tighten screws evenly.
8. Reconnect the wiring harness firmly.
9. Restore power and water, then check for leaks and allow time for ice production.

Quick checks after installation

• Confirm the shutoff arm moves freely and is in the “on” position.
• Make sure the fill tube is seated and not kinked or blocked.
• Verify the freezer temperature is set cold enough (most side-by-sides make ice best around 0°F).
• Watch the first fill cycle for drips or spraying.

Common symptoms and what they usually mean

Symptom	Most common cause	What we check next
No ice after install	Water not reaching ice maker	Water supply valve open; line not kinked; inlet valve operation
Small or hollow cubes	Low water flow	House water pressure; restricted line; inlet valve
Leaking into ice bin	Misaligned fill tube or overfill	Fill tube position; ice maker seating; valve seepage

If water is not filling the new ice maker, the water valve feeding the ice maker can be the issue; for this model, we often check the refrigerator inlet valve WP2315576.

Why it matters

A properly installed ice maker on Kenmore 1069530682 prevents water leaks, protects the freezer from ice buildup, and restores normal cube size and harvest timing. Matching the correct assembly also avoids wiring and mounting fit problems.

Last updated: February 2026

The most common problems we see on Kenmore side-by-side refrigerators like model 1069530682 are poor cooling, ice maker or water dispenser failures, water leaks, and unusual noises. These symptoms usually come from airflow restrictions, defrost system trouble, worn door seals, or a failing fan, thermostat, or inlet valve.

Common symptoms and likely causes

• Not cooling or warm temperatures: dirty condenser coils, evaporator fan not moving air, or defrost failure causing ice buildup
• Freezer cold but fresh food warm: weak evaporator airflow, iced-over evaporator, or blocked vents
• Ice maker not making ice: water supply issue, inlet valve not opening, or ice maker failure
• Water leaking: clogged defrost drain, cracked water line, or door not sealing and sweating
• Buzzing, rattling, grinding: fan blade rubbing ice, worn fan motor, or items vibrating

Quick checks before replacing parts

• Set temps to about 0°F (freezer) and 37°F (refrigerator)
• Keep vents clear; do not pack food tightly against air outlets
• Look for heavy frost on the freezer back panel (points to defrost trouble)
• Trace leaks to the dispenser area, under crispers, or under the cabinet
• Listen for steady fan airflow; scraping often means ice contact

Common replacement parts for model 1069530682

Problem area	What typically fixes it	Model-matched example
Ice maker not working	Replace ice maker assembly	Ice maker assembly 4317943
Warm temps or erratic cycling	Replace cold control thermostat	Refrigerator thermostat WP2198202
Frost buildup, warm fridge	Replace defrost bi-metal	Refrigerator defrost bi-metal WPW10225581
No water to ice/dispenser	Replace inlet valve	Refrigerator inlet valve WP2315576

Why it matters

Cooling, ice, and leak complaints are often connected. A defrost or airflow problem can raise temperatures, create excess frost, and lead to water on the floor when ice melts.

Helpful DIY guidance

Use Kenmore 106 model refrigerator error codes to match symptoms to likely systems, and how to prevent water dispenser and ice maker problems to reduce repeat water and ice issues.

Last updated: February 2026