Owner’s manual
Error Codes
How big is the Kenmore Coldspot refrigerator?
For Kenmore Coldspot side-by-side refrigerator model 10650049717, use the product dimensions section in the 10650049717 owner's manual for the exact height, width, and depth. For planning purposes, most Kenmore 106 side-by-side units are roughly 66 to 71 inches tall and 30 to 34 inches deep (without handles).
We use these checks to avoid surprises with cabinet openings, door swing, and moving the refrigerator through doorways.
- Check the dimensions/specifications pages in the 10650049717 owner's manual
- Measure your unit at the widest and deepest points (hinges and handles often add depth)
- Measure with doors closed and then confirm door swing clearance next to a wall
- Compare your measurements to the kitchen cutout (width, height, and depth)
- Plan for ventilation space so the refrigerator cools efficiently
The Kenmore manual calls for these minimum clearances for ventilation and door swing:
- 1/2 inch of space on each side and at the top
- 2 inches of space behind the refrigerator
- At least 2 inches on the hinge side when installed next to a fixed wall (door swing clearance varies by setup)
Use this only as a rough fit check; confirm exact specs in the manual.
| What you are checking | Typical range for side-by-side refrigerators | Why it matters |
|---|---|---|
| Height | 66 to 71 in. | Fits under cabinets and through doorways |
| Depth (no handle) | 30 to 34 in. | Prevents sticking out past counters |
| Clearance behind | 2 in. | Airflow and cooling performance |
Correct sizing prevents poor airflow, warm temperatures, and doors that cannot open fully against a wall. It also helps you plan water line routing if your 10650049717 has an ice maker.
If you are ordering replacement parts while you plan the install, you can shop model-matched parts on the list for 10650049717 or search by model on Sears PartsDirect.
Last updated: February 2026
Where can I find a Kenmore fridge model?
You can find the model number for your Kenmore refrigerator on the model and serial label, which is typically inside the fresh food (refrigerator) compartment on a side wall or ceiling area. For Kenmore model 10650049717, the exact label location and what it looks like are shown in the owner's manual.
Look in these spots first (use a flashlight and wipe away any condensation or dust):
- Inside the refrigerator compartment on the left or right side wall
- On the ceiling of the refrigerator compartment near the light housing
- Behind or beside the crisper drawers (sometimes on the wall behind the lower drawers)
- On the inside edge of the refrigerator door (hinge side)
- Behind the base grille or near the kickplate area at the bottom front
Once you find the tag, copy the information exactly as printed.
- Model number: the full identifier (example: 10650049717)
- Serial number: used to identify production date and revision
- Color code or suffix: may appear after the model family (common on Kenmore 106 models)
| What you need | What it’s used for | Why it matters |
|---|---|---|
| Model number | Parts lookup and diagrams | Ensures the part fits your exact configuration |
| Serial number | Version and production run | Helps match updated parts when designs change |
| Product type | Troubleshooting steps | Confirms you are following the right procedure |
Kenmore 106 model refrigerators often have multiple variations that look similar. Using the exact model number from the label helps us match the correct parts (like a door switch, ice maker, or water filter housing) and the right repair instructions.
If you are ordering parts after you locate the model number, you can also search by model on Sears PartsDirect.
Last updated: February 2026
Why is my Kenmore Elite side by side refrigerator leaking water?
Water leaks on a Kenmore 10650049717 side-by-side refrigerator usually come from a clogged defrost drain overflowing, a loose water-line connection at the back, or dripping at the dispenser from air in the lines after a new filter or installation. Use the owner's manual to match the symptom to the right fix.
Check these common spots before replacing parts:
- Front dispenser area: a few after-drops are normal; steady dripping points to air in lines or ice melting in the chute
- Behind the refrigerator: water line fittings not fully tightened
- Under the freezer side or front floor: defrost drain backed up and spilling
- Inside fresh food section: water line or reservoir seep, depending on puddle location
The manual notes a few drops after dispensing are normal. For ongoing dripping:
- Hold the glass under the dispenser 2 to 3 seconds after releasing the lever
- Dispense several glasses to purge air in the water lines after a filter change
- Clear ice shavings in the chute so meltwater does not mimic a leak
- Pull the unit out and inspect the household shutoff and inlet connection
- Tighten fittings firmly (avoid overtightening plastic)
- Dry the area, then recheck for fresh moisture
- Unplug the refrigerator
- Melt visible ice near the drain opening
- Clear debris so water flows to the drain pan underneath
| Where you see water | Most likely cause | Best first step |
|---|---|---|
| Dispenser area | Air in lines or after-drip | Flush water system; hold cup 2 to 3 seconds |
| Back of unit | Loose connection | Tighten fittings; recheck |
| Freezer side floor | Defrost drain clog | Clear drain; confirm pan flow |
- Refrigerator water tube W10823511 for cracked or leaking water tubing
- Refrigerator housing assembly W11162041 for leaks around the water filter housing
Stopping the leak prevents floor damage and reduces ice buildup that can interfere with airflow and cooling.
For replacement parts for model 10650049717, use the parts list for this model or search by model number on Sears PartsDirect.
Last updated: February 2026
