Kenmore 11021112022 laundry, residential, washer Parts

To hard reset your Kenmore washer model 11021112022, unplug it (or switch off the breaker) for 2 minutes, then restore power and run a cycle. This clears many temporary control glitches; if problems return, run the model’s diagnostic or calibration steps in the 11021112022 owner's manual.

Hard reset steps (power reset)

• Press Power/Cancel to stop the cycle.
• Unplug the washer or turn OFF the circuit breaker.
• Wait 2 minutes (this lets the control fully discharge).
• Restore power.
• Select a normal cycle and press Start.

If the washer still acts up: do these quick checks

A reset will not fix a mechanical failure or a drain or fill problem. Before you chase parts, we recommend:

• Confirm the washer is plugged into a grounded 3-prong outlet (no extension cord).
• Make sure both water faucets are fully open and inlet hoses are not kinked.
• Verify the lid closes firmly; a lid lock issue can look like a “won’t start” problem.
• If the washer will not drain, check the drain hose routing and standpipe height.
• If the washer is shaking or walking, re-level the feet (leveling reduces noise and vibration).

Common “reset didn’t help” symptoms and likely causes

Symptom after reset	What to check first	Related part (if needed)
Won’t start or stops immediately	Lid lock engagement, lid strike alignment	Lid lock-sol W11700916, washer lid strike W11457841
Won’t fill or fills slowly	Screens in inlet valve, water pressure, hose kinks	Washer water inlet valve W11165546
Won’t drain	Drain hose, pump obstruction, pump operation	Pump assembly, drain W11399437

Why it matters

A hard reset is a fast way to clear a control-board “hang” after a power flicker or interrupted cycle. If the same symptom returns, the washer is usually reacting to a real condition (lid lock, draining, filling, or leveling) that needs correction.

Last updated: January 2026

Most Kenmore washers, including model 11021112022, typically last 10 to 15 years with normal household use. Lifespan depends most on load size, detergent choice (HE detergent), installation, and routine maintenance such as hose replacement and periodic cleaning outlined in the 11021112022 washer installation & care manual.

Typical lifespan ranges (what we see most often)

These ranges help set expectations for a residential washer like the Kenmore 11021112022.

• 10 to 15 years: typical life expectancy for most Kenmore washers
• 8 to 12 years: heavy use (large families, frequent bulky loads)
• 12 to 18 years: lighter use plus consistent care (proper leveling, correct detergent, good ventilation)
• 5 years for inlet hoses: replace to reduce risk of hose failure (a common preventable issue)

Usage pattern	What usually shortens life	What helps most
Heavy, daily loads	Overloading, frequent unbalanced spins	Smaller loads, redistribute items
Normal household use	Skipping cleaning and inspections	Monthly cleaning routine
Occasional use	Long periods of non-use with water left in system	Non-use and vacation care steps

Maintenance that extends washer life

We recommend following the care steps in your manual and focusing on the items that most often cause early failures.

• Use High Efficiency (HE) detergent and avoid over-dosing
• Keep the washer level to reduce vibration and drivetrain wear
• Inspect fill hoses for bulges, kinks, cuts, wear, or leaks
• Replace inlet hoses at 5 years and mark the replacement date
• Run a cleaning cycle periodically to reduce residue and odors
• Avoid storing or operating the washer below 32°F to prevent freeze damage

Parts that commonly wear as a washer ages

If performance changes over time (no spin, won’t drain, loud noise), these are common wear items on many Kenmore top-load platforms.

• Drive belt W11239857 (slipping, squealing, weak spin)
• Pump assembly, drain W11399437 (won’t drain, slow drain, humming)
• Washer water inlet valve W11165546 (no fill, slow fill, hot or cold water issues)
• Lid lock-sol W11700916 (won’t start, lid won’t lock)

Why it matters

A washer that is installed correctly and maintained (especially hoses and cleaning) usually reaches its full expected lifespan and avoids sudden leaks, drain problems, and vibration-related wear.

Last updated: January 2026

On a Kenmore washer like model 11021112022, the F-22 code points to a door or lid lock system problem (the control is not sensing the lock correctly). The most common fixes are checking the lock, strike, and wiring, then restoring power.

What to check first (quick, safe steps)

• Unplug the washer for 2 minutes, then plug it back in (this resets the control).
• Make sure the lid closes fully and nothing is caught between the lid and top.
• Inspect the lid strike for cracks, looseness, or misalignment.
• Listen for the lock to click when you start a cycle.
• Confirm the outlet is a grounded 3-prong outlet and avoid extension cords (power issues can cause false lock errors).

For model-specific operating and safety guidance, follow the troubleshooting and electrical notes in the 11021112022 owner's manual.

Parts that commonly cause an F-22 style lock error

If the lid will not lock, locks then immediately unlocks, or the washer will not start, these parts are common suspects:

• Lid lock-sol W11700916 (lock mechanism and lock sensing)
• Washer lid strike W11457841 (the plastic strike the lock grabs)
• Lower wiring connections (loose plug, corrosion, pinched harness)

Symptoms and likely causes

What you notice	Most likely cause	What we recommend
Won’t start, no lock “click”	Lid lock not engaging	Check strike alignment; test/replace lid lock
Starts then stops with F-22	Intermittent lock signal	Reseat connectors; inspect harness; replace lock if worn
Lid closes but feels “off”	Broken/loose strike	Replace strike; verify lid closes squarely

Why it matters

The lid lock is a safety system. If the washer cannot confirm the lid is locked, it may stop to prevent spinning with the lid open, which protects you and prevents damage to the basket and drive system.

Last updated: January 2026