Kenmore 66560629000 microwave/hood combo Parts

For Kenmore microwave/hood combo model 66560629000, the overall product dimensions are 29-7/8 inches wide, 16-1/4 inches high, and 15-3/8 inches deep (front to back). These measurements come from the model’s installation specifications in the installation guide.

Dimensions at a glance

Measurement	Size (inches)	What it means
Width	29-7/8	Fits a 30-inch wide minimum opening
Height	16-1/4	Overall unit height
Depth	15-3/8	Cabinet face to back of unit

What to measure before you buy or install

To avoid fit issues with cabinets, venting, and the mounting plate, we recommend checking these items:

• Cabinet opening width: at least 30 inches
• Upper cabinet depth: typically 12 to 14 inches is recommended for service access
• Clearance to cooktop: 30 inches minimum from the cooking surface to the bottom of the microwave
• Wall structure: 2x4 wood studs and appropriate wall covering support
• Power and vent path: confirm outlet location and whether you are venting outside or recirculating

Why it matters

Microwave/hood combos like the Kenmore 66560629000 are designed around standard 30-inch cabinet openings, but depth and clearance drive real-world fit. Getting the depth and cooktop clearance right helps prevent door interference, poor ventilation performance, and difficult servicing later.

Ordering parts for this model

If you are measuring because you are replacing a damaged exterior piece (such as the vent grille or door components), you can order model-matched replacement parts from the parts list for 66560629000, or search by model on Sears PartsDirect.

Last updated: February 2026

To change the over-the-range light bulb on your Kenmore microwave/hood combo model 66560629000, we unplug power, remove the vent grille and bulb cover, replace the bulb with a candelabra-base 30-watt bulb, then reinstall the cover and grille and restore power. See the step-by-step in the owner's manual.

Before you start (safety and prep)

• Unplug the microwave or switch off power at the breaker.
• Let the cooktop light area cool completely.
• Use a small Phillips screwdriver for grille and cover screws.
• Handle the bulb with a clean, dry cloth (helps prevent premature failure).
• Do not run the vent fan without the grease filters installed.

Steps to replace the cooktop (over-stove) light bulb

1. Disconnect power.
2. Remove the two vent grille mounting screws (the two outer screws above the cover).
3. Slide the top of the vent grille out, then pull the bottom forward to remove the grille.
4. Open the bulb cover.
5. Replace the bulb with a candelabra-base 30-watt bulb.
6. Close the bulb cover.
7. Reinstall the vent grille (top in first, then snap the bottom in) and reinstall the screws.
8. Restore power and test the light.

Bulb type and part options

For model 66560629000, the manual specifies a candelabra-base 30-watt bulb.

Item	What to use	Notes
Bulb base	Candelabra base	Small screw-in base
Wattage	30W max	Higher wattage can overheat the cover
OEM light part	Lamp assembly 8206232A	Matches the manual’s Part No. 4393681 reference

Why it matters

Using the correct 30-watt candelabra bulb helps prevent melted covers, repeated burnouts, and heat damage around the vent grille and light housing.

If you want the exact OEM light assembly for this model, we list it on the parts list for 66560629000, and you can also search by model number on Sears PartsDirect.

Last updated: February 2026

Yes. Kenmore sells microwaves, including over-the-range microwave/hood combo models like Kenmore 66560629000. Kenmore-branded microwaves use standard microwave components (such as a magnetron, turntable system, and door interlock switches) and are supported with model-specific documentation like the 66560629000 owner's manual.

What types of Kenmore microwaves are common?

Kenmore microwaves are typically sold in a few main styles; your 66560629000 is an over-the-range microwave/hood combo.

• Over-the-range microwave/hood combo: mounts above the cooktop and includes an exhaust fan and cooktop light
• Countertop microwave: sits on the counter and plugs into a standard outlet
• Built-in microwave: installs into cabinetry (often with a trim kit)
• Microwave drawer: installs below the counter and opens like a drawer

How to confirm what you have (fast checks)

Use these quick identifiers to match the appliance type and order the right parts.

• Check the model tag inside the door area; it should read 66560629000
• Look for a bottom vent fan and cooktop light (common on over-the-range units)
• Confirm whether it vents outside or recirculates through a charcoal/grease filter
• Match parts by model number before ordering (door parts and vent parts vary by design)

Parts you can replace on this Kenmore model

If you are maintaining or repairing the microwave/hood combo, these are common service parts available for model 66560629000.

Symptom	Common part area	Example part on this model
Not heating	High-voltage circuit	Diode W11256462
Light out	Cooktop light	Lamp assembly 8206232A
Door won’t start unit	Door interlock system	Primary switch W10211972
Poor venting or rattling grille	Vent trim	Microwave/hood grille vent 8184599

Why it matters

Kenmore is a brand name used across multiple appliance types, so the model number is what ensures you get the correct microwave parts, installation details, and safe operating instructions. For ordering beyond the parts list for 66560629000, search by model number on Sears PartsDirect.

Last updated: February 2026

To reset your Kenmore microwave/hood combo model 66560629000, unplug it (or turn off the breaker) for about 1 minute, then restore power. This clears most temporary control glitches and restores normal operation; you will typically need to set the clock again (see the 66560629000 owner's manual).

Quick reset options (from easiest to most effective)

• Power reset: Unplug for 60 seconds, then plug back in.
• Breaker reset: Turn the microwave circuit breaker off for 60 seconds, then back on.
• Control lock check: If the keypad seems “dead,” make sure Control Lock is not enabled (the 66560629000 owner's manual shows the exact key sequence).
• Clock re-set: After power returns, set the clock so timed features work correctly.
• Door check: Open and close the door firmly; a misaligned door can prevent the microwave from starting.

If the microwave still will not run after a reset

A reset fixes software-like glitches; it will not correct a failed safety switch, blown fuse, or high-voltage heating problem.

What to check first

• Display on but won’t start: Door not fully latching or an interlock issue.
• No display at all: Power supply problem, internal fuse/thermal protection issue.
• Runs but does not heat: Likely a heating circuit component issue.

Common parts involved (model 66560629000)

Symptom	Common area	Example part on this model
Won’t start, intermittent start	Door interlock system	Primary switch W10211972
Dead, no power	Thermal protection	Thermal fuse W11707984
Runs but not heating	High-voltage circuit	Diode W11256462

Why it matters

Resetting is the fastest way to clear a stuck control state after a power flicker or keypad glitch. If symptoms return quickly, the issue is usually a door interlock, thermal fuse, or high-voltage component, not the control settings.

For parts ordering, use the parts list for model 66560629000 or search by model number on Sears PartsDirect.

Last updated: February 2026

On Kenmore microwave/hood combo model 66560629000, an E12 code indicates the control detected an abnormal condition and stopped normal operation. Start with a hard power reset and basic power checks; then use the troubleshooting section in the 66560629000 owner's manual to match the code to the correct circuit.

What to do first (safe, no-tools checks)

• Turn the circuit breaker OFF for 1 minute, then turn it ON.
• Confirm the breaker is not tripped and any house fuse is not blown.
• Make sure the power cord is fully seated in the outlet.
• Clear the display and run a short 30-second heat test with a cup of water.
• If E12 returns immediately, stop using the microwave until it is diagnosed.

What E12 commonly points to on over-the-range microwaves

E-codes on over-the-range microwaves are most often triggered by a problem the control can detect, such as a door interlock switch not changing state correctly, a thermal safety device opening, or a control/connection issue.

Quick symptom-to-system guide

What happens with E12	Most likely area to check	Example part on this model
Code appears when closing or starting	Door interlock circuit	Primary switch W10211972
Code appears after running briefly	Overheat or safety cutout	Thermal fuse W11707984
Unit is dead or resets randomly	Power supply connection	Check cord and outlet; see 66560629000 installation guide

Why it matters

When the control sees a safety-related fault, it can disable heating and fan functions to prevent damage. Fixing the underlying cause prevents repeat shutdowns and protects high-voltage components.

Getting the right parts

If testing shows a failed switch or fuse, order the exact replacement for model 66560629000 from the parts list, or search by model number on Sears PartsDirect.

Last updated: February 2026