Kenmore 79074512910 free standing gas range Parts

Yes. Kenmore makes gas ranges, including the Kenmore 79074512910 free standing gas range; it is a gas cooking appliance with surface burners and a gas oven that uses electric ignition for normal operation (as described in the 79074512910 use & care guide).

What “Kenmore gas range” means for this model

Kenmore is the brand on the appliance, and 79074512910 is a gas range platform covered in the manual under model series 790.7451* and 790.7452*.

Typical features you can expect on this type of Kenmore gas range:

• Gas surface burners with knob controls
• Gas oven burner with electric ignitor for lighting
• Oven venting that needs clear airflow for proper combustion
• Standard household electrical power required for ignition and controls

Important operation notes (gas + electric ignition)

The oven on this style of range relies on electric ignition, so power matters for baking.

• Do not try to operate the electric-ignition oven during a power failure
• If power goes out, turn oven controls to OFF
• Surface burners can be lit with a match during an outage (use extreme caution)
• Keep the oven vent and airflow around the base unobstructed

Quick reference: surface burners vs. oven during a power outage

Function	What usually works without power	What to do
Surface burners	Can be lit manually	Light with a match, then turn knob to LITE carefully
Oven bake/broil	Electric ignition will not light	Keep controls OFF until power returns

Why it matters

Knowing that 79074512910 is a Kenmore gas range helps you choose correct parts and troubleshoot correctly. For example, “no bake heat” often points to the oven ignition system, such as the bake igniter 316489403.

Last updated: February 2026

A Kenmore gas range like model 79074512910 typically lasts 15 years with normal household use. Consistent cleaning, correct gas setup, and fixing weak ignition or uneven flames early help you reach that lifespan; see the maintenance guidance in the 79074512910 use and care guide.

What affects lifespan the most

• Cleaning habits: grease and spills left on burners and in the oven increase wear.
• Ignition health: slow or failed lighting strains igniters and can lead to no-heat symptoms.
• Flame quality: steady blue flames indicate good combustion; persistent orange flames can point to setup or air quality issues.
• Door seal condition: a leaking seal makes the oven work harder to hold temperature.
• Proper installation and gas conversion: incorrect LP conversion or regulator issues can cause performance problems.

Quick maintenance checklist (monthly and as-needed)

• Wipe burner heads, caps, and the cooktop after boilovers.
• Keep burner ports clear (use a soft brush; do not enlarge ports).
• Confirm the oven preheats normally and holds temperature.
• Inspect the oven door gasket for gaps, tears, or flattening.
• Replace dim or failed oven lights with the correct bulb type.

Common “wear” items vs. long-life components

Item	Typical role	When it shortens lifespan
Igniter	Lights the bake burner	Slow ignition, no bake heat
Temperature sensor	Helps regulate oven temperature	Overheating, underheating, error symptoms
Door seal	Keeps heat in the oven cavity	Longer preheat times, uneven baking
Pressure regulator	Maintains correct gas pressure	Weak flames, inconsistent heating

If your oven is slow to heat or won’t ignite, the bake igniter is a frequent fix on gas ranges; for this model, the bake igniter 316489403 is a common replacement part.

Why it matters

A gas range that is clean, properly adjusted, and heating efficiently runs fewer extended cycles. That reduces stress on key parts like the igniter, gas valve, and controls, helping your 79074512910 reach the expected 15-year service life.

Last updated: February 2026

On the Kenmore 79074512910 free standing gas range, we remove the cooktop (top) by taking off the grates and burner pieces first, then releasing the fasteners so the main top can lift up for service. Follow the steps in the 79074512910 owner's manual for your exact burner style and handling notes.

Before you start (safety and prep)

• Turn all burner knobs to OFF and let the range cool completely.
• Shut off the gas supply at the manual shut-off valve.
• Unplug the range (or switch off the circuit breaker).
• Protect the countertop and the cooktop surface with a towel or cardboard.
• Keep screws organized by location; lengths can vary.

Steps to remove the cooktop (main top)

1. Remove the surface burner grates.
2. Lift off the burner caps.
3. If your model uses removable burner heads, remove them; if the heads are secured, clean and service them in place.
4. Look for mounting screws near the burner bases, under the front lip, or along the rear edge; remove the screws.
5. If burner tubes or brackets are fastened to the underside of the top, remove those screws as needed.
6. Lift the cooktop from the front and raise it; some versions hinge up, others lift off after the rear tabs release.

What you may need to remove (varies by configuration)

Component	Usually removed first?	Why it matters
Grates	Yes	Clears access to burner parts and fasteners
Burner caps	Yes	Lets you access burner heads and screws
Burner heads	Sometimes	Needed if screws are under the head
Cooktop mounting screws	Yes	Releases the main top so it can lift

Why it matters

Removing the top correctly prevents bent gas tubes, cracked porcelain, and misaligned burner caps that can cause weak flames or ignition problems. After reassembly, make sure caps are seated firmly on the burner heads.

Last updated: February 2026

On the Kenmore 79074512910 gas range, an oven that “stops working” is usually caused by a power interruption, a weak/failed bake igniter that cannot open the gas valve, or a sensor/control problem that prevents proper ignition and temperature control. Use the 79074512910 owner's manual “Before You Call” section to narrow it down.

Quick checks we recommend first

• Confirm the range has power; after an outage, turn the oven off, restore power, then reset the clock and oven function.
• Verify the oven is actually set to Bake with a temperature selected.
• Confirm gas supply: shutoff valve is open and other gas appliances work.
• Start Bake and watch for ignition: the igniter should glow before the burner lights.
• If the igniter glows but there is no flame, the igniter is still the top suspect.

Most common causes (and the parts involved)

• Weak bake igniter: glows but draws too little current to open the gas valve; replace with bake igniter 316489403.
• Bad oven temperature sensor: can cause no-heat, overheating, or shutdowns; use frigidaire range oven temperature sensor 316490000 if it matches your model’s wiring and mounting.
• Control or wiring issue: loose connection, damaged wire, or a failing control can stop ignition commands.
• Burner or gas valve problem: restricted burner ports or a failing valve can prevent a steady flame.

Symptom guide

What you see	Most likely cause	Best next step
No heat and no igniter glow	Power, control, wiring	Verify power, then follow manual checks
Igniter glows, no flame	Weak igniter (most common)	Replace igniter first
Heats sometimes, then quits	Sensor, control, loose connection	Inspect connections; test sensor

Why it matters

A weak igniter or faulty sensor causes underheating, long preheats, or repeated ignition attempts; fixing the root cause restores reliable bake performance and consistent temperatures.

Last updated: February 2026

On Kenmore gas range model 79074512910, the model and serial number are printed on the identification plate attached to the oven frame. You can access it by opening the storage drawer, warmer drawer, or broiler drawer (depending on your range configuration); see the 79074512910 owner's manual for the exact location diagram.

Where to look on model 79074512910

Check these common spots in this order:

• Open the storage drawer and look on the lower right oven frame
• If your range has a warmer drawer, open it and check the right-hand oven front frame
• If your range has a broiler drawer, open it and check the right-hand oven front frame
• Look for an identification plate with model, serial, and sometimes a lot number/letter

What information to copy (and why)

When you contact service or order parts, we recommend copying everything from the plate.

Label item	What it’s used for
Model number (example: 79074512910)	Matches the correct parts diagrams and assemblies
Serial number	Helps confirm production run and compatible revisions
Lot number/letter (if shown)	Helps narrow down exact configuration

Why it matters

Kenmore ranges often have multiple versions that look similar. Using the exact model and serial from the identification plate helps us match the right igniter, sensor, burner parts, and control components the first time.

Last updated: February 2026