Sears 702207310 single handle combination tub & shower faucet Parts

The model number for your Sears single handle combination tub and shower faucet is typically printed on the original packaging and paperwork; on the faucet itself, it is most often found on the valve body behind the handle and trim. Use the exact model number to match repair parts.

Where to look on the faucet

Shut off the water supply first, then check these common locations:

• Behind the handle: remove the handle and look on the valve body casting
• Behind the escutcheon (trim plate): the back side of the plate or the wall-side of the valve
• On a tag or sticker: sometimes attached to the supply lines or valve body
• On the tub spout or diverter area (less common)
• On your purchase receipt, installation invoice, or saved product paperwork

Quick access steps (no special tools)

1. Turn off water at the stops or main shutoff.
2. Remove the handle set screw and pull the handle.
3. Slide off the trim sleeve; loosen and remove the escutcheon if needed.
4. Wipe the valve body clean and look for stamped or molded numbers.

What the model number should look like

For this Sears faucet, the model number format is:

Item	Example	Why it matters
Model number	702207310	Ensures correct cartridge, seats/springs, and trim compatibility
Brand	Sears	Helps narrow diagrams and repair kits

Why it matters

Tub and shower faucets often have multiple cartridge and trim variations that look similar. Using the exact model number prevents ordering the wrong cartridge, O-rings, or handle hardware.

For help confirming the number before ordering, use [how to find your appliance model number (and what it means for parts)].

Last updated: March 2026

To troubleshoot your Sears 702207310 single handle combination tub and shower faucet, start by identifying the symptom (drip, low flow, temperature issues, or diverter problems) and then isolate whether the cause is the cartridge, mineral buildup, or a supply issue. Most fixes involve cleaning or replacing wear parts.

Symptom-based checks

• Drips from tub spout/showerhead when off: cartridge or seats/seals worn
• Low flow: clogged showerhead/aerator, debris in cartridge, partially closed stops
• Temperature swings: failing cartridge, pressure imbalance, hot-side restriction
• Water comes from tub spout during shower: diverter worn or spout diverter failing
• Leak at handle/trim: O-ring or cartridge seal, loose retaining nut

Step-by-step troubleshooting (safe order)

1. Confirm both hot and cold shutoff valves are fully open.
2. Check the showerhead for scale; clean or temporarily remove to test flow.
3. If symptoms persist, shut off water and remove the handle and trim.
4. Inspect for a loose retaining nut/clip and signs of corrosion or mineral buildup.
5. Pull the cartridge; look for torn seals, scoring, or debris.

Quick diagnosis table

What you see	Most likely cause	Typical next step
Drip that worsens over time	Cartridge wear	Replace cartridge and seals
Flow improves with showerhead removed	Clogged showerhead	Descale or replace showerhead
Leak only when turning handle	Handle seal/O-ring	Replace O-ring, verify tightness

Why it matters

Troubleshooting by symptom prevents unnecessary wall or valve-body work. In many cases, restoring proper sealing and clearing debris returns normal pressure and temperature control.

If you need basic tools for the job, use [must have tools for appliance repair].

Last updated: March 2026

A single handle combination tub and shower faucet like Sears model 702207310 typically lasts 15 to 20 years. In most homes, the cartridge and seals wear out sooner and are the parts most commonly replaced to extend the faucet’s life.

What usually wears out first

These components determine real-world lifespan more than the valve body:

• Cartridge (causes dripping, temperature swings, low flow)
• O-rings and seals (causes leaks behind the wall or at the handle)
• Diverter (causes water to leak from the tub spout when showering)
• Handle hardware (stripped set screw, loose handle)
• Mineral buildup in passages (reduces flow and affects mixing)

Lifespan factors (what changes the number)

Factor	Effect on lifespan	What you can do
Hard water/mineral scale	Shortens cartridge and seal life	Periodic cleaning, consider water treatment
High water pressure	Increases wear and leak risk	Keep pressure in a typical 40 to 80 PSI range
Frequent use	More cycles, faster wear	Replace cartridge at first signs of drift/drip

Signs it is near end-of-life (or needs a rebuild)

• Drips from the tub spout or showerhead when off
• Handle gets stiff or gritty
• Temperature is hard to control or suddenly changes
• Water leaks at the handle or behind the trim

Why it matters

Most “faucet failures” are serviceable wear parts, not a bad valve body. Replacing the cartridge and seals early prevents water damage and keeps the shower temperature stable.

For safety basics before any DIY work, review [are diy appliance repairs safe].

Last updated: March 2026