Kenmore Elite 58077127710 room air conditioner Parts

Kenmore air conditioners are a solid choice for dependable cooling when they’re correctly installed and maintained. For the Kenmore Elite 58077127710 (12,000 BTU), the 58077127710 use & care guide outlines normal operation, common noises, and basic troubleshooting that help keep performance consistent.

What “good” looks like in real use

A good room air conditioner cools steadily, runs without frequent short-cycling, and drains moisture the right way.

• Cools the room without turning on and off rapidly
• Maintains set temperature with stable airflow
• Has normal operating sounds (gurgle/hiss, swishing) rather than grinding or squealing
• Drains water to the outside (or into the base pan) without dripping indoors
• Responds reliably to the control panel and remote

Reliability depends most on installation and maintenance

Even a high-quality Kenmore Elite unit can seem “bad” if airflow or drainage is compromised.

Factor	What you want	What causes complaints
Airflow	Clean filter, open vents	Dirty filter, blocked grille
Drainage	Slight tilt to the rear	Level or forward tilt causing indoor drips
Noise	Normal air movement and water sounds	Vibration from poor window support
Cycling	Longer, steadier run times	Rapid cycling from restricted airflow

Quick checks we recommend first

These steps solve many “not cooling” or “annoying noise” complaints without parts replacement.

• Clean the air filter to restore airflow
• Confirm the unit tilts slightly downward toward the rear for proper drainage (do not drill the drain pan)
• If it cycles rapidly in extreme heat, set fan speed to the fastest setting for maximum cooling
• Reduce vibration by tightening the window kit and improving support
• If the remote is inconsistent, verify you’re within range of the sensor

When a part is the likely fix

If you’ve confirmed airflow and installation are correct and the issue persists, an electrical or control issue becomes more likely.

• Intermittent power or dead unit: inspect cord and connections; consider the power cord EAD63469531
• Random operation or no response: consider the electronic control board EBR83604002
• Display issues: consider the display board EBR83548611

Why it matters

A room air conditioner’s cooling performance is tightly tied to airflow and drainage. Keeping the filter clean and the cabinet properly supported prevents rapid cycling, water leaks, and vibration, which are the most common reasons a unit gets labeled “not good.”

Last updated: February 2026

To reset your Kenmore Elite room air conditioner model 58077127710, use the reset (current interrupter) on the power cord plug: press TEST, then press RESET so it stays engaged. This restores power after a trip and is the correct “reset” for this unit.

Reset steps (power cord TEST/RESET)

• Turn the air conditioner OFF.
• Locate the TEST and RESET buttons on the plug head.
• Press TEST; the RESET button should pop out.
• Press RESET firmly.
• Turn the unit back ON and wait up to 3 minutes for the compressor delay.

If RESET will not stay engaged

If the RESET button pops back out or will not latch, stop using the air conditioner and have the outlet/circuit and the unit checked by a qualified technician. A tripping interrupter can indicate an electrical fault that needs correction.

Quick checks after a reset

• Make sure the plug is pushed completely into the outlet.
• Check the home breaker/fuse and reset/replace if needed.
• Avoid extension cords; plug the unit directly into a dedicated outlet.
• If the unit was turned off and on quickly, wait 3 minutes before restarting.

What “reset” does (and does not) do

Action	What it affects	When to use it
TEST/RESET on power cord	Restores power after the cord safety device trips	Unit will not start, cord device tripped
Turning unit OFF then ON	Normal restart (with compressor delay)	After changing settings or a brief power interruption

Why it matters

Using the cord’s TEST/RESET correctly helps protect the unit and your home wiring. It also prevents unnecessary parts replacement when the real issue is a tripped interrupter or a simple power problem.

For model-specific operating details and troubleshooting, follow the 58077127710 owner's manual.

Last updated: February 2026

For a Kenmore Elite room air conditioner like model 58077127710, the system is best understood as two main sections: the indoor (evaporator) side that absorbs heat from the room, and the outdoor (condenser) side that releases that heat outside. Together, they move heat out of your space to cool it.

What each “side” does

• Evaporator (indoor side): pulls warm room air across the evaporator coil; heat is absorbed and cooler air is blown back into the room.
• Condenser (outdoor side): dumps that absorbed heat outdoors through the condenser coil.
• Compressor (between both sides): pumps refrigerant through the sealed system so heat can be moved efficiently.
• Fans: move air across each coil (indoor airflow and outdoor airflow).

For model-specific diagrams and component names, use the 58077127710 owner’s manual.

Room AC vs. central AC (quick comparison)

System type	“Two parts” usually means	Where they are located
Window/room air conditioner (58077127710)	Evaporator section + condenser section (in one cabinet)	Both inside one unit; indoor side faces the room, outdoor side faces outside
Central HVAC	Indoor air handler/evaporator + outdoor condenser unit	Split between inside (furnace/air handler area) and outside

Why it matters

Knowing the two sections helps with troubleshooting: if the unit runs but does not cool, we focus on airflow across the evaporator (filter, indoor fan) and heat rejection at the condenser (outdoor coil, condenser fan), plus the compressor and controls.

Related parts customers commonly replace

If you are diagnosing airflow or control issues on this model, these parts are commonly involved:

• Room air conditioner electronic control board EBR83604002 (power, modes, cooling commands)
• Room air conditioner evaporator fan blade MDG58298301 (indoor airflow)
• Room air conditioner condenser fan blade 5900A10009E (outdoor airflow)

Last updated: February 2026

On Kenmore Elite model 58077127710, a CH code on the display indicates the unit has detected a fault condition and needs service attention. Use the troubleshooting and error-code guidance in the 58077127710 owner's manual; if the display shows CH, follow the manual’s service steps or contact Sears PartsDirect support.

What CH-34 typically points to

On many Kenmore Elite smart room air conditioners built on LG-style electronics, CH-34 is commonly associated with a high-pressure or discharge pressure protection event. When discharge pressure rises too high, the control can shut the compressor off to protect the sealed system.

Common triggers include:

• Dirty or blocked condenser coil (restricted heat rejection)
• Outdoor airflow restriction (unit too close to a wall, blocked louvers)
• Condenser fan problem (blade damage, motor not running, loose clamp)
• Overheating from extreme outdoor temperatures or direct sun
• Installation issues that trap hot exhaust air

What we recommend you do first (safe checks)

1. Unplug the air conditioner for 5 minutes, then restore power.
2. Clean the filter and make sure the front intake is not blocked.
3. Check the rear of the unit for lint, leaves, or debris on the condenser.
4. Confirm the unit has clearance for airflow and is not recirculating hot air.
5. Listen for the condenser fan; if the compressor tries to start but the fan does not, stop using the unit.

Parts that can be involved (if airflow or fan is the issue)

Symptom	Likely area	Example part for this model
Fan runs intermittently or not at all	Fan motor or wiring	Room air conditioner fan motor EAU61423711
Loud vibration or scraping	Fan blade or clamp	Room air conditioner condenser fan blade 5900A10009E
Unit dead or acts erratic	Controls/power	Room air conditioner electronic control board EBR83604002

Why it matters

A CH-34 style high-pressure event is a protective shutdown. Repeated trips can overheat components and reduce cooling performance, so restoring proper airflow and fan operation is the fastest way to prevent repeat errors.

Last updated: March 2026