Kenmore Elite 11010018000 laundry work surface Parts

The Kenmore Elite 11010018000 is a laundry work surface, not a washer tub, so it does not have a cubic-foot capacity rating. Instead, it is sized to fit over a 27-inch-wide front-load washer and dryer pair and adds about 3 inches of height (see the 11010018000 owner's manual).

A washer’s “cubic feet” refers to the wash basket volume. This Kenmore Elite accessory is a countertop-style surface used for sorting, treating, and folding laundry.

What we can size instead of cubic feet:

• Fits over two appliances that are each 27 in. wide
• Requires about 1 in. spacing between washer and dryer for alignment pads
• Adds about 3 in. to the overall height of the washer and dryer
• Not intended for ironing (heat can discolor the surface)

Use this checklist to confirm your laundry pair is compatible:

• Both machines are front-loading and sit side-by-side
• Both are level side-to-side and front-to-back
• Both are the same height (height difference no more than about 3/8 in.)
• You can maintain about 1 in. gap between them
• You have a measuring tape and a level

If you are shopping by “cubic feet,” you are likely comparing washer capacity. For model 11010018000, the right comparison is fit and clearance: correct width, spacing, and leveling prevent rocking, rubbing, and poor alignment.

If you need a cosmetic replacement for the top, we list the matching badge as the medallion W10058450. You can also search by model number on Sears PartsDirect to find other compatible Kenmore parts.

Last updated: February 2026

For Kenmore Elite model 11010018000, you’ll find the model and serial number on a printed label attached to the appliance. On most Kenmore washers, that label is typically on the back of the control panel, along the cabinet frame, or around the door opening (front-load). Use the exact model number to match parts and documentation in the owner's manual.

Check these spots in order; we recommend using a flashlight and snapping a photo of the label:

• Top-load washers: under the lid near the tub opening, or on the cabinet rim
• Top-load with rear console: back of the control panel or behind the console
• Front-load washers: inside the door opening, on the door jamb, or behind the door
• All styles: side of the main cabinet near the bottom edge, or the rear panel

Record the full model number and serial number exactly as shown. This helps ensure the right fit for parts and accessories.

• Match every digit; Kenmore numbers can look similar (for example, missing a zero changes the model).
• If the label is worn, take a photo and zoom in; cleaning dust off first helps.
• When ordering cosmetic pieces for this laundry work surface setup, use the model number to confirm fit; for example, the medallion W10058450 is a model-matched part listed for this unit.

Kenmore Elite model numbers control parts compatibility. Using the exact model number prevents ordering the wrong trim, hardware, or accessories and helps you pull the correct diagrams and instructions. If you want to search beyond the parts listed for this model, we also support model lookups on Sears PartsDirect.

Last updated: February 2026

For Kenmore Elite model 11010018000 (Elite laundry work surface), the fastest way to track down discontinued parts is to search by the exact model number and the original part ID, then confirm fit and dimensions in the owner's manual before you buy. When an exact part is unavailable, we match by function and measurements.

Use these details first because they prevent ordering a look-alike that will not fit.

• Use the full model number: 11010018000
• Search by the exact part ID when you have it (example: W10058450)
• Compare the part name and what it does (example: medallion is cosmetic, not structural)
• Confirm the appliance type: Elite laundry work surface (not a washer or dryer)
• Verify key fit requirements from the manual (washer and dryer width and spacing)

If you need a replacement badge or emblem, we list the medallion for this model as an orderable part.

• Order the medallion W10058450 from the parts list for model 11010018000
• If you are not sure it matches your finish or location, compare it to your original before removing it
• For broader model searches and additional parts lookups, use Sears PartsDirect

This model is a work surface that sits on top of a washer and dryer pair. The manual calls out common fit constraints that matter when you are trying to substitute parts or accessories.

Discontinued parts are often replaced by revised versions or compatible alternatives. For a work surface, small differences in spacing, leveling, or pad placement can cause vibration, rubbing, or poor alignment, even when the part looks correct.

Last updated: February 2026