Kenmore 79551032011 refrigerator Parts

Your Kenmore Elite refrigerator model 79551032011 is about 30.6 cubic feet of total capacity. This is the overall storage volume for the fresh food and freezer sections combined; exact usable space varies with shelves, bins, and the ice maker setup.

How to confirm the capacity on your exact unit

We recommend checking the model and rating label and then matching it to the specifications in the 79551032011 owner's manual.

• Look for the rating label inside the fresh food compartment (often on a side wall).
• Confirm the model number is 79551032011 (not a similar 795 prefix model).
• Check the “Specifications” section for total capacity (cu. ft.).
• If your shelves or bins are missing, usable space can feel smaller even when capacity is the same.

What “cubic feet” means (and what it does not)

Cubic feet is a volume measurement used to compare refrigerator sizes. It does not tell you the exact shelf layout or how much you can fit on each level.

Measurement	What it describes	What to expect
Total capacity (cu. ft.)	Overall interior volume	Used for model-to-model comparisons
Usable space	Space you can practically load	Changes with ice bin, shelves, and door bins
Exterior size	Width/height/depth	Not directly tied to cu. ft.

Why it matters

Knowing the capacity helps when you are comparing replacement refrigerators, planning kitchen fit, or troubleshooting storage complaints (for example, a full ice container can reduce freezer room). If you need to restore storage space, replacing broken bins and slides can make the interior usable again.

Last updated: January 2026

For Kenmore side-by-side refrigerator model 79551032011, the most reliable way to confirm exact height, width, and depth is to use the model’s published specifications in the 79551032011 owner’s manual. Most side-by-side units in this class are roughly 32 to 36 inches wide, 65 to 71 inches tall, and 28 to 34 inches deep (including handles).

How to measure your refrigerator (so the numbers match real life)

Use a tape measure and record all three dimensions; we recommend measuring twice because trim, hinges, and handles can change fit.

• Width: measure the cabinet at the widest point; then measure again including handles
• Height: floor to top of hinge cover (not just the cabinet)
• Depth: front of doors/handles to the back; also note clearance behind for the water line
• Door swing clearance: measure how far doors need to open to remove bins and drawers
• Ventilation space: leave room at the top and back for airflow

Typical dimension ranges (what to expect)

These ranges help with planning when you are comparing spaces, but the manual specs are what you should use for a final fit.

Measurement	Typical range for side-by-side refrigerators	Why it varies
Width	32 to 36 in.	cabinet size and handle style
Height	65 to 71 in.	hinge cover height and leveling legs
Depth	28 to 34 in.	handles, door thickness, rear clearance

Why it matters

Accurate dimensions prevent delivery issues, door-swing interference, and poor cooling from restricted airflow. Getting the right measurements also helps when planning water line routing for the dispenser and ice maker.

Last updated: January 2026

On the Kenmore 79551032011 side-by-side refrigerator, the water filter is typically located inside the refrigerator compartment or behind a small filter door in the base grille area (often at the bottom front). Use the 79551032011 owner's manual to confirm the exact location for your configuration.

Common water filter locations on side-by-side models

Most Kenmore side-by-side refrigerators place the filter in one of these spots:

• Inside the refrigerator compartment, upper right corner
• Inside the refrigerator compartment, lower left corner
• Behind a flip-down or push-to-open filter cover in the base grille (bottom front)
• Behind a small access door near the bottom of the fresh food section

How to find it quickly

We recommend this quick check order:

1. Look in the upper right of the fresh food section for a twist-in or push-in filter.
2. Check the lower left inside wall of the fresh food section.
3. Inspect the bottom front grille area for a small filter door.
4. If you see a filter housing but no cartridge, confirm the correct cartridge style in the manual.

What you should see (by location)

Location	What it looks like	Typical removal style
Inside fresh food section	Filter head or short cylinder housing	Twist quarter-turn or push-and-turn
Base grille (bottom front)	Small door or round cap behind grille	Push button, pull straight out, or twist

Why it matters

Finding the correct filter location helps you replace the cartridge without cracking the filter head, damaging water lines, or causing leaks that can lead to low water flow at the dispenser and poor ice production.

For step-by-step replacement tips that apply to many Kenmore refrigerators, use how to replace the water filter in a Kenmore refrigerator.

Last updated: January 2026