Samsung DG68-00882A-01 owner manual Parts

Most Samsung electric ranges, including the Samsung DG68-00882A-01 electric range covered by our documentation, are installed with a separate range power cord that matches your home outlet (3-prong or 4-prong); the cord is typically purchased separately. For model-specific installation and electrical details, use the DG68-00882A-01 owner's manual.

What you should buy (and why)

A range cord must match both your wall receptacle and the range terminal block connection.

• Choose 3-prong if your home has a 3-slot range outlet (common in older installations)
• Choose 4-prong if your home has a 4-slot range outlet (common in newer installations)
• Use a UL-listed range cord
• Match the cord to the circuit rating (most electric ranges use 40A or 50A circuits)
• Replace a cord that is cut, brittle, overheated, or loose at the plug

Quick comparison: 3-prong vs 4-prong

Cord type	Typical outlet	Grounding method	When it’s used most often
3-prong	3-slot	Neutral bonded to chassis (by configuration)	Older homes/outlets
4-prong	4-slot	Separate equipment ground	Newer homes/outlets

Safety checks before you install or replace a cord

Working at the terminal block involves high voltage. We follow these basics every time:

• Turn off power at the circuit breaker before touching wiring
• Confirm the outlet and cord are not loose, scorched, or damaged
• Do not pinch the cord behind the range; keep it clear of sharp edges
• Make sure the cord is routed through the strain relief so it cannot pull on connections
• If you smell burning or see smoke, disconnect power immediately and stop using the range

Why it matters

Using the correct cord prevents poor connections that can overheat, trip breakers, or cause the range to lose power during baking or broiling. The manual also emphasizes avoiding damaged cords and loose wall sockets for electrical safety.

Ordering help

If you do not see the cord or accessory you need listed for this model, we recommend searching by your full model number on Sears PartsDirect to find compatible electrical accessories.

Last updated: February 2026

For a Samsung range/oven like model DG68-00882A-01, a replacement electronic oven control board (often listed as a PCB) typically costs about $150 to $300 for the part alone; total repair cost is higher if you add labor and a service call. See the DG68-00882A-01 owner's manual for control-panel and troubleshooting details.

What affects the price most

• Exact model and revision: Samsung uses different PCB versions across similar ranges.
• Which board you need: main control board (EOC/PCB) vs. display/interface board.
• Availability: discontinued or limited-stock boards usually cost more.
• New vs. refurbished: refurbished boards can cost less (when offered).
• Labor: diagnosis and installation often add significant cost.

Quick cost breakdown (typical)

Item	Typical range	Notes
Control board part	$150 to $300	Most common range for Samsung electric ranges
Labor (if hired)	$150 to $350	Varies by region and access to the control area
Service/diagnostic fee	$75 to $150	Sometimes applied toward the repair

How to confirm you actually need a control board

A failed control board can look like several other problems. Before buying a PCB, we recommend these checks:

• Reset power: shut off the breaker for 30 seconds, then restore power.
• Look for error codes: codes such as C-d0 (key short) or C-31 (PCB temperature abnormal) can point toward control or sensor issues.
• Rule out simple causes: stuck keypad, loose wiring connector, or heat damage near the control area.
• Check related components: oven temperature sensor, door lock/latch (self-clean), and harness connections.
• Use proper test tools: a multimeter helps confirm power and continuity before replacing electronics.

Why it matters

Control boards are one of the most expensive range parts; confirming the failure first helps you avoid replacing a PCB when the real issue is a sensor, wiring, or a door-lock circuit problem.

If you do decide to move forward, order using the parts list for your exact model, or search by model number on Sears PartsDirect.

Last updated: February 2026

Most Samsung electric ranges use a dedicated 240/120V (or 208Y/120V) single-phase, 60 Hz range connection with either a 3-prong (3-wire) or 4-prong (4-wire) plug, depending on your home’s outlet. For DG68-00882A-01, confirm the exact cord and connection requirements in the DG68-00882A-01 owner's manual.

What you should expect for a range outlet

In most U.S. homes, an electric range is set up one of these two ways:

• 4-prong (4-wire) outlet and cord (common in newer installations)
• 3-prong (3-wire) outlet and cord (common in older installations)
• A dedicated circuit sized for an electric range (do not share with other appliances)
• A properly grounded connection (critical for safety)

Quick comparison: 3-prong vs 4-prong

Feature	3-prong (3-wire)	4-prong (4-wire)
Prongs/wires	3	4
Grounding method	Neutral bonded to frame (typical older setup)	Separate ground wire (typical newer setup)
When you’ll see it	Many homes built before the mid-1990s	Many homes built after the mid-1990s

Installation notes that affect the plug choice

The plug type is determined by the wall receptacle and local electrical requirements, not by preference. Also, many ranges are sold without a power cord installed, so you match the cord to your outlet.

• Match the cord to the existing outlet (3-prong or 4-prong)
• Turn off power at the circuit breaker before any wiring work
• Use the strain relief and terminal block connections shown in the manual
• If the cooktop glass is cracked, switch off and unplug the range before use

Why it matters

Using the correct cord and wiring method helps prevent nuisance tripping, overheating at the terminal block, and shock risk. It also helps your Samsung range operate correctly on 208V or 240V service.

For parts and accessories, start with the parts list for DG68-00882A-01; you can also search by model number on Sears PartsDirect.

Last updated: February 2026

If your Samsung range model DG68-00882A-01 has surface burners that work but the oven will not heat, the most common causes are a power supply issue to the oven circuit, incorrect control settings, or a failed oven component such as the temperature sensor, heating element, or control board. Start with the quick checks below, then follow the troubleshooting table in the DG68-00882A-01 owner's manual.

Quick checks (fastest fixes first)

• Confirm the range is fully plugged into a live, properly grounded outlet.
• Reset the circuit breaker (or replace a blown fuse) even if the cooktop still works.
• Make sure the oven controls are set correctly (Bake temperature and Start/On pressed).
• If the oven was just used, let it cool down and try again (some conditions prevent operation when overheated).
• If there was a recent power interruption, turn the oven off, then restart after power is stable.

What’s usually happening (cooktop works, oven doesn’t)

Many electric ranges can appear “partly powered” if one leg of a 240V supply is missing. In that situation, the cooktop or lights may still run on 120V, while the oven heating circuit will not operate correctly.

Symptom	Most likely direction	What to do next
Display works, cooktop heats, oven won’t heat	Power supply or control setting	Check breaker, outlet, settings
Oven won’t turn on at all	Power, wiring, or control issue	Verify outlet power, then inspect wiring
Error code like C-20 or C-21 appears	Oven sensor or over-temp condition	Power reset, then sensor diagnosis

If you see an information code

The manual lists oven-related codes such as C-20 (sensor open) and C-21 (abnormally high internal temperature). Use this sequence:

• Press OVEN OFF.
• Disconnect power to the range for at least 30 seconds, then restore power.
• Retry Bake.

Why it matters

When the oven will not heat but the stovetop works, the issue is often electrical (breaker, wiring, or a missing power leg). Fixing the power supply problem first prevents unnecessary part replacement and helps protect the control board and wiring.

Parts and diagrams

We recommend using the model-based diagrams and parts list for DG68-00882A-01 to match the correct oven sensor, bake element, or control components; you can also search by model on Sears PartsDirect.

Last updated: February 2026