Goodman PGB036100-1A package gas Parts

A 36,000 BTU (3-ton) air conditioner like the cooling section used in many Goodman package gas units (including model PGB036100-1A) typically cools about 1,200 to 1,800 square feet. The real number depends most on insulation, ceiling height, sun exposure, and your local climate.

Typical coverage range (what to expect)

Most 36,000 BTU systems land in this range when the home is reasonably sealed and insulated:

• 1,200 to 1,400 sq ft: hot climates, lots of sun, older windows, or high ceilings
• 1,400 to 1,600 sq ft: average conditions in many homes
• 1,600 to 1,800 sq ft: mild climates, good insulation, shaded windows

Quick sizing table

Use this as a practical starting point for a 36,000 BTU unit.

Home conditions	Typical sq ft cooled	What changes the result most
Hot, sunny, leaky home	1,200 to 1,400	Solar gain, air leaks
Average insulation and windows	1,400 to 1,600	Duct losses, occupancy
Well-insulated, shaded, tight home	1,600 to 1,800	Humidity load, ventilation

Why the same BTU can cool different square footage

Cooling capacity is only part of comfort. These factors often matter more than the nameplate BTU:

• Humidity (high humidity reduces effective comfort and increases runtime)
• Duct condition (leaks or poor insulation can waste a lot of cooling)
• Airflow (dirty filters, weak blower, or blocked returns reduce delivered cooling)
• Ceiling height (more air volume to cool)
• Window area and shading (direct sun can add major heat load)

When to look at parts (comfort and airflow issues)

If your PGB036100-1A runs constantly, freezes up, or cools unevenly, airflow and fan operation are common culprits. Parts that can be involved include:

• Central air conditioner air handler blower motor B13400313S (indoor airflow)
• Central air conditioner condenser fan motor B13400251S (outdoor heat rejection)
• Overload CAP050300440RSP (can affect compressor circuit protection)

Why it matters

Oversizing can cause short cycling and poor dehumidification; undersizing can lead to nonstop running and higher energy use. Matching capacity to the home’s heat load and keeping airflow healthy is what delivers steady comfort.

For ordering replacement parts for your Goodman PGB036100-1A, use the parts list for this model or search by model number on Sears PartsDirect.

Last updated: February 2026

Common problems we see on Goodman AC and package gas units like model PGB036100-1A include no cooling, weak airflow, short cycling, unusual noises, and no-heat or ignition issues. Many are caused by airflow restrictions, electrical component failures, or venting and burner problems.

Most common symptoms and what they usually point to

• Not cooling or trips the breaker: weak run capacitor, failing condenser fan motor, wiring issues
• Weak airflow: dirty filter, blocked return/supply, blower motor or capacitor problems
• Outdoor fan not running or loud: failing fan motor or damaged fan blade
• Short cycling: overheating from restricted airflow, limit switch opening, control or capacitor issues
• No heat or ignition problems (gas heat section): inducer/venting problems, burner/manifold issues

Parts that commonly fail on this model

If your troubleshooting points to a failed component, these are common replacements for the PGB036100-1A:

• Overload CAP050300440RSP
• Central air conditioner condenser fan motor B13400251S
• Central air conditioner condenser fan blade B1086756S
• Central air conditioner limit switch, 180-degree 1370901S
• Furnace inducer vent motor assembly B2959000S

Quick checks we recommend before replacing parts

1. Thermostat settings: confirm mode (cool/heat) and setpoint.
2. Airflow basics: replace the filter, open registers, clear debris around the unit.
3. Power: check the disconnect, breakers, and any service switch.
4. Coil condition: dirty coils reduce heat transfer and can cause shutdowns.
5. Listen and observe: humming (capacitor), grinding (motor), repeated clicking (controls/ignition).

Symptom-to-likely-cause guide

Symptom	Likely cause	Common related part
Fan hums but won’t start	Weak capacitor or motor issue	Condenser fan motor
Unit runs but doesn’t cool	Airflow restriction or refrigerant issue	Blower motor (airflow side)
Shuts off quickly	Overheating, limit opening	Limit switch
No heat, draft issues	Inducer/venting problem	Inducer vent motor assembly

Why it matters

Package units depend on correct airflow and stable electrical performance. A simple restriction (filter, coil, duct) can trigger limit trips, short cycling, higher energy use, and premature motor or capacitor failures.

For model-specific replacement options and availability, order from the parts list for PGB036100-1A or search by model on Sears PartsDirect.

Last updated: February 2026

The model number is printed on your Goodman package gas unit’s rating plate (data tag). For model PGB036100-1A, look for a label that lists the model and serial; it’s typically inside a service panel or on the cabinet near the gas and electrical connections.

Where to look on a Goodman PGB036100-1A package unit

Check these common rating-plate locations:

• Inside the main control/access panel (remove the screws and lift off the panel)
• On an interior bulkhead near the blower compartment
• On the burner/heat section panel near the gas valve area
• On an exterior cabinet wall near where the electrical conduit enters
• Near the refrigerant service valves area (behind a small access cover)

What the label should show

On the data tag, confirm you see:

• Model: PGB036100-1A
• Serial number: a longer code used for manufacturing date tracking
• Electrical: voltage and phase (for example, 208/230V)
• Gas: fuel type and input rating

Quick check: model vs. serial

Item	What it’s used for	Example format
Model number	Identifies the exact unit configuration for parts	PGB036100-1A
Serial number	Identifies production run and date coding	Longer alphanumeric string

Why it matters for parts

Goodman package units can look similar across series, but parts like a blower motor, condenser fan motor, or inducer assembly can vary by model and revision. Matching the rating-plate model helps ensure the correct replacement part.

If you are already on the PGB036100-1A parts list, you can cross-check common components like the furnace inducer vent motor assembly B2959000S against what’s installed.

Last updated: March 2026