- Kenmore refrigerator water filters
- Whirlpool refrigerator water filters
- Samsung refrigerator water filters
- GE refrigerator water filters
- LG refrigerator water filters
- Frigidaire refrigerator water filters
- KitchenAid refrigerator water filters
- Maytag refrigerator water filters
- Kenmore Elite refrigerator water filters
- Estate refrigerator water filters
- GE Profile refrigerator water filters
- Amana refrigerator water filters
- Bosch refrigerator water filters
- Dacor refrigerator water filters
- Electrolux refrigerator water filters
Top DIY repair help
View All Repair Categories
Appliances
Lawn & Garden
Power Tools
Home Improvement
Sports & Leisure
Heating & Cooling
Husqvarna Lawn Mower Height Adjuster, Left 581497907
Part #581497907
GenuineOEM
This part is no longer available.We've permanently sold out of this part. It's no longer available from the manufacturer and the manufacturer has no substitute for this part. Although our call center staff is always happy to help when possible, they don't have access to this part. If you can't find that part and decide to replace the product, we invite you to visit www.sears.com
Confirm this part fits
Part Information
Basic Information
- Part Name: Lawn Mower Height Adjuster, Left
- Manufacturer: Husqvarna
- Category: Lawn Mower
- Primary Function: Adjusts the lawn mower deck height
Installation & Compatibility
- Compatible Models:Fits various Husqvarna lawn mower models. Please confirm this part is correct for your model before ordering.
- Installation Difficulty: Easy ? straightforward replacement with basic tools
- Tools Required: Standard wrench set
Additional Information
The Husqvarna Lawn Mower Height Adjuster, Left (part number 581497907), adjusts the mower deck height by raising or lowering the wheels. It replaces part numbers 408017, 409097, 409108, 438460, 532431143, and 581497904.
If you're noticing uneven cutting or trouble adjusting the deck height, the height adjuster may be worn or damaged. Replacing it helps restore level cutting and makes height adjustments easier.
Use a standard wrench set for installation. Disconnect the spark plug wire and wear gloves to protect your hands. This durable part helps keep your lawn mower cutting clean and even all season long.
ReviewsJuly 23, 2019|wallyw, MDJuly 11, 2019|Papa W, Stillman Valley ILLINOISJuly 05, 2019|Maddog w c, Mass.June 26, 2019|BOZOP, EAGLEVILLE PAAugust 19, 2018|TeDeJo63, TulsaAugust 07, 2018|Tom70again, Maple Shade, N.JJune 09, 2018|Chevy427, Cherry Hill njMay 15, 2018|Loader, Ft Walton Beach Fl
0 Reviews
Install in proper order
The product was exactly what I needed. Much better, and just a little more expensive, than trying to piece together old, worn parts with a new wheel bearing. Craftsman will indeed sell only the bearing, but it is very hard to install because of a compression spacer and a snap ring (requiring a special tool.) Through trial and error, I found the proper order to install the new height adjuster, which includes a pre-installed new bearing. (see YouTube video https://www.youtube.com/watch?v=QiT8mlHceWA.) Disassembly of old adjuster: 1. Remove wheel (if you have a new wheel, you won't need this) 2. Remove gear by removing C-clip (save them for later) 3. Remove Pin, it has a head and only comes out one way (save Pin for later) Notes: Mark or take note of direction. Pin has pressure from compressed spacer, so it will be difficult to remove. You might try compressing the spacer. This problem is noted in the video. 4. Remove plastic cover and washer (save them for later)) 5. Unscrew old adjuster from lawnmower (2 nuts under mower, save them for later) Note: One nut is close to the transmission. As you unscrew, you might have to pull the old adjuster out a little to remove this nut. Assembly 1. Install Pin from step 3 above. Notes: Try to use the same direction as in step 3, but it might not matter. There might be pressure, so it might involve some compression. This problem is noted in the video. 2. Install adjuster using nuts from step 5 above. Note: Start both nuts with new adjuster pulled out a little, then tighten both. 3. Install plastic cover (and washer) from step 4 above 4. Install gear using C-clip from step 2 above. 5. Install wheel
Ease of InstallationModerate
Duration of Installation30 minutes - 1 hour
verified customer
2 people thought this review was helpful.
Hard then it should have been.
My eyes aren't as good as they once were, all and all it wasn't to bad of an install.
Ease of InstallationEasy
Duration of Installation1 - 2 hours
verified customer
Was this review helpful?
Fitting was great
Gear and wheel were worn out when I installed them I saw the shaft bearing was gone also ( mounted on the height adjuster ) . All good now thanks.
Ease of InstallationEasy
Duration of Installation30 minutes - 1 hour
verified customer
Was this review helpful?
NOT TO HARD TO INSTALL
TOOK A LITTLE TIME MY MOWER IS OLDER AND HAD TO CLEAN AREA TO PUT NEW PART ON MOWER WORKS GREAT NOW
Ease of InstallationModerate
Duration of Installation30 minutes - 1 hour
verified customer
Was this review helpful?
Was easy to install
Took a few minutes to install, same as replaced. Nice to have level mow and not have to remow area to get level. No more wire to try and tie all parts together.
Ease of InstallationVery Easy
Duration of InstallationLess than 30 minutes
verified customer
Was this review helpful?
Not too bad to install
Looked difficult but not bad at all. 15 minutes start to finish
Ease of InstallationEasy
Duration of Installation30 minutes - 1 hour
verified customer
Was this review helpful?
Thanks
Easy to install, with hand tools,in about 15 minutes
Ease of InstallationVery Easy
Duration of Installation30 minutes - 1 hour
verified customer
1 person thought this review was helpful.
Easy to install and fitted perfect
The part was easy to install. Suggest the mower be up at saw horse level and the mower hangs over the two 2.x4 I had straddle the horses. It made it easy to get to the two bolts and the drive shaft for the front wheel drive is right there and was easy to reinstall in the adjuster. I did both sides so it was a snap.
Ease of InstallationVery Easy
Duration of InstallationLess than 30 minutes
verified customer
1 person thought this review was helpful.
Average Customer Ratings
Overall Rating
Popular Models Using 581497907 Part
Model Number
Model Name
Model Number
96122000700
Parts & More
Carpet Cleaner
Cooktop
Dishwasher
Dryer
Exercise Cycle
Gas Line Trimmer
Gas Walk-Behind Mower
Microwave/Hood Combo
Power Rake
Rear-Engine Riding Mower
Wall Oven