Craftsman 917377070 rotary lawn mower Parts

Common problems we see on the Craftsman 917377070 rotary lawn mower include no-start conditions (stale fuel, dirty air filter, spark issues), loss of power, uneven cutting, excessive vibration from a worn or loose blade, and drive problems that make the mower hard to push or slow to move. See the 917377070 owner's manual troubleshooting chart for model-specific checks.

• Won’t start: out of fuel, stale fuel, water in fuel, dirty air filter, spark plug wire off, bad spark plug, control bar not held to the handle
• Loss of power: dirty air filter, grass buildup under the deck, cutting too much grass at once, too much oil in the engine
• Uneven cut: worn or bent blade, wheel heights set unevenly, debris packed under the mower
• Excessive vibration: loose blade bolt, bent blade, broken blade adapter, bent crankshaft
• Hard to push or drive slows: heavy grass drag, cutting height too low, debris under deck, drive system wear

1. Drain old gas and refill with fresh, clean gasoline.
2. Inspect and clean or replace the air filter.
3. Confirm the spark plug wire is firmly connected; replace the spark plug if fouled.
4. Tip the mower safely (spark plug wire disconnected) and clear grass buildup under the deck.
5. Inspect the blade and blade mounting hardware; replace worn parts as needed.

Catching these issues early helps prevent bigger damage (especially vibration-related problems) and keeps your Craftsman walk-behind mower cutting cleanly and starting reliably throughout the season.

Last updated: February 2026

For the Craftsman rotary lawn mower model 917377070, we recommend a high-quality detergent 4-cycle engine oil that meets API service classification SG-SL, using SAE 30 for warmer conditions and 5W-30 or 10W-30 for easier cold-weather starting (with more frequent oil-level checks). See the 917377070 owner's manual for the temperature chart and maintenance intervals.

Use 4-cycle detergent oil (not 2-cycle mix). Choose viscosity by outdoor temperature:

• SAE 30: best for typical warm-weather mowing
• 5W-30: improves starting in cold weather
• 10W-30: also helps in cooler temps, common and easy to find
• API rating SG-SL (or higher) on the bottle
• Keep the oil level at the full mark; low oil can damage the engine

These are the common choices the manual supports; match oil to your mowing weather.

The manual’s maintenance guidance for this mower is straightforward:

• Check crankcase oil before starting
• Recheck oil after every 5 hours of continuous use
• Change oil every 25 hours of operation
• Change oil at least once per year even if you do not reach 25 hours

Correct viscosity and a proper oil level keep the 4-cycle engine cooler and better lubricated, which reduces wear and helps prevent hard starting, smoking, and premature engine damage.

Last updated: February 2026

The model number is 917.377070 (often written without the dot as 917377070). This Craftsman rotary lawn mower’s owner’s manual lists it on the cover as “Model No. 917.377070”; it matches the parts diagrams for this exact mower.

We use the model number to match the correct parts (blade, drive system, handle hardware) for your specific Craftsman walk-behind mower.

• Check the model tag/label on the mower deck (typically near the rear or side of the deck)
• Look on the rear housing area near the bagger door or discharge chute
• Check near the handle mounting brackets
• Confirm the number matches the format 917.377070 or 917377070

The fastest way to confirm you have the right model is to compare the manual cover and the illustrated parts list.

For reference, the model number appears in the 917377070 owner’s manual.

Craftsman model numbers can look similar across different mowers and tractors. Using 917377070 ensures you get the correct rotary lawn mower parts, such as the drive control assembly, wheel components, and deck hardware.

Last updated: February 2026

The model number for this Craftsman rotary lawn mower is 917.377070 (often written without the dot as 917377070). You’ll see it printed on the cover of the owner's manual and on the mower’s model and serial number label.

We recommend matching the model number in at least two places to avoid ordering the wrong parts.

• Check the model and serial number label on the mower deck (typically near the rear or side of the deck)
• Compare it to the model number shown on the manual cover
• Use the full model number when searching parts diagrams and lists
• If the label is dirty or faded, clean it gently and re-check the digits

The same model can appear with or without punctuation.

Craftsman walk-behind mowers can look similar across years, but parts like the drive control, wheel hardware, and blade components vary by model. Using 917.377070 helps ensure the correct fit for items such as the lawn mower drive control 583230601 or the lawn mower 21-in deck 3-in-1 blade 532189028.

Last updated: February 2026

A 42-inch Craftsman riding mower deck belt size depends on the exact tractor model and deck configuration; it is not determined by deck width alone. Your Craftsman rotary lawn mower model 917377070 is a 21-inch walk-behind mower and uses a drive system (not a 42-inch deck belt). Use the 917377070 owner's manual to confirm your mower’s drive components and part identification.

• If the mower has a seat and steering wheel, it is a riding mower (often 42-inch deck).
• If you walk behind it and it has a 21-inch cutting path, it is a walk-behind mower like 917377070.
• A 42-inch deck belt question usually applies to a Craftsman tractor model number (different format and label location).
• For walk-behind mowers, the “belt” is typically a self-propel drive belt (if equipped), not a deck belt.
• The most accurate match comes from the model number tag and the parts diagram.

Because 42-inch Craftsman decks vary by tractor series and idler layout, belt sizes commonly fall into a few ranges.

On Craftsman 917377070, common drive-related service items include the drive control and wheel drive hardware. If you are troubleshooting self-propel movement, these model-matched parts are often involved:

• Lawn mower drive control 583230601 (control assembly that manages drive engagement)
• Lawn mower idler pulley 532166043 (maintains belt tension in the drive system)
• Check wheel drive pieces like dust covers, E-rings, and pinion assemblies for wear or binding

Ordering by “42-inch belt” alone often leads to the wrong part because small differences in deck routing and idler pulleys change belt length. Matching by model number prevents repeat repairs and protects the drive system from slipping or premature wear.

Last updated: February 2026

Craftsman model 917377070 is identified by its model number, not a build year. The year is determined from the mower’s product identification label (date code/serial information), then matched to the date-code format shown in the 917377070 owner's manual.

Look for the product ID label in common spots on a Craftsman walk-behind mower:

• On the rear of the deck near the discharge opening
• On the top of the deck near the engine mounting area
• On the back panel behind the bagger door area
• Near the handle mounting brackets
• On the frame area above the rear wheels

Once you find the label, write down:

• Model number (should read 917377070)
• Serial number or date code (varies by production run)
• Engine model information (often Briggs & Stratton on this mower)

Many Craftsman mowers use a date-code format on the label that can be read as month, day, year (for example, MMDDYY). Use the label code, not the model number, to determine the year.

Knowing the correct year helps us match the right Craftsman parts (blade, drive control cable, wheels, and hardware) and avoid ordering look-alike parts that do not fit your exact production run.

• Drive system parts (drive control, pulleys, pinion assemblies)
• Wheel and height adjust components
• Blade and blade adapter
• Handle and control bar hardware

Last updated: February 2026