This drive shaft and shifter assembly (part number WH38X10017) is for washers.
Drive shaft and shifter assembly WH38X10017 connects the motor with the washplate, and shifts the drive system between agitate and spin.
Unplug the washer before installing this part. Wear work gloves to protect your hands.
Frequently Bought Together
We have 15,000+ available parts
Washer Tub Mounting Hub Washer
Part #WH2X1199
In Stock
$7.64
12% OFFÂ Phone Price : $8.64
Qty
Washer Tub Seal Assembly
Part #WH02X10383
In Stock
$11.13
15% OFFÂ Phone Price : $13.13
Qty
Washer Tub Bearing
Part #WH2X1198
In Stock
$31.53
16% OFFÂ Phone Price : $37.53
Qty
Washer Outer Tub
Part #WH45X20473
In Stock
$191.76
6% OFFÂ Phone Price : $203.76
Qty
Washer Drive Pulley
Part #WH07X10019
In Stock
$70.98
8% OFFÂ Phone Price : $76.98
Qty
Washer Hub Nut
Part #WH2X1193
In Stock
$14.47
12% OFFÂ Phone Price : $16.47
Qty
Reviews
0 Reviews
washing machine shifter
December 30, 2020|Bill, Hanover, Pa. 17331
Perfect fit and easy to install. Just a few screws to install
Ease of InstallationVery Difficult
Duration of Installation30 minutes - 1 hour
verified customer
Yes, I would recommend this to a friend
Was this review helpful?
easier to install than to take apart
November 03, 2020|pablo, denver
The parts description was not very clear, but the seal shown in the picture does come with the assembly, so don't order a new seal! Getting the old rusty nut off the shaft was a bear... had to finally split it to get it off. The rest was not very hard.
Ease of InstallationDifficult
Duration of InstallationMore than 2 hours
verified customer
Yes, I would recommend this to a friend
Was this review helpful?
Time consuming repair.
September 16, 2019|Rayman1940, South Carolina
Requires complete tear down of washing machine. Regret I did not replace tub bearing at same time, however it is not as involved to go back in later to replace that part. Bottom pulley nut was very tight used impact gun to remove. When installing drive belt used zip tie on motor shaft to keep belt from riding up did not need special installation tool. View installation videos on line to understand this step.
Ease of InstallationDifficult
Duration of InstallationMore than 2 hours
verified customer
1 person thought this review was helpful.
No more grinding
January 27, 2019|Lucky M, Orlando, FL
You'll need the scanner wrench. You will also need to clean out the threads between the shaft and the threads. The shaft is not round. You can get a small pick or drill bit to get the calcium buildup out so you can turn the nut. It took away the grinding I was hearing during the wash cycle. Well worth it. Not much to a washer as far as they are built. I replaced the motor twice, the pump once and the seal. It comes with the seal.
Ease of InstallationEasy
Duration of Installation30 minutes - 1 hour
verified customer
1 person thought this review was helpful.
Correct part for the job
March 01, 2021|LGM1, Sterling Hts, mi
About a 3 hour job if the tub nut breaks free. You will probably need to get the spanner tool. I had to heat nut with torch to get it too loosen. Wear gloves when removing part, lots of sharp edges.
Ease of InstallationDifficult
Duration of Installation1 - 2 hours
verified customer
Yes, I would recommend this to a friend
Was this review helpful?
Difficult to remove had to order special tool.
June 23, 2018|Mario1, Tucson
Took a lot of work to remove nut the holds tub. Had to order special tool. Hammered on the tool and finally got it loose had to have someone hold shaft to complete removal.
verified customer