Owner’s manual
Will any miter saw stand work with any miter saw?
No. A miter saw stand is not automatically universal; you need to match the stand’s mounting method to the mounting holes in the base of your Craftsman 137212060 miter saw, or mount the saw to a plywood adapter plate and then clamp or bolt that plate to the stand. See the owner's manual for the model’s mounting-hole guidance.
Most stands work when you can securely attach the saw without twisting, rocking, or shifting during a cut.
- Mounting hole pattern: the stand’s brackets must line up with the saw base holes, or you need an adapter plate.
- Fastening method: bolts and lock nuts are more secure than friction-only clamps.
- Stability: the stand must not flex when the motor starts or when you slide the head through a cut.
- Work support: extension wings or rollers must support long stock without lifting the saw.
- Safe operation: the saw must not “walk” or tip during use.
Your manual describes two common, reliable ways to mount this saw using the four mounting holes in the base.
| Use case | Best approach | What you’ll need |
|---|---|---|
| Stationary shop setup | Bolt saw directly to a bench | Hex bolts, washers, lock washers, nuts (hardware purchased separately) |
| Portable or stand setup | Bolt saw to 3/4-inch plywood, then clamp or bolt plywood to the stand | 3/4-inch plywood, bolts for the saw base, C-clamps or stand hardware |
Use this checklist to avoid a stand that “sort of” fits but is unsafe.
- Measure the distance between the four base mounting holes on the saw.
- Confirm the stand supports the saw’s base footprint without overhang that causes rocking.
- Verify you can use through-bolts (not just sheet-metal screws) for the saw-to-stand connection.
- Check that the stand’s extensions support your typical material length.
- After mounting, push on the saw from multiple directions; it should not shift.
A stand that does not match the mounting holes or cannot be tightened securely can let the saw move unexpectedly. That affects cut accuracy and increases the risk of the workpiece shifting. The manual’s mounting method (bench mount or plywood mount) is designed to keep the saw stable during operation.
If you need to look up diagrams or confirm you have the correct model number before ordering hardware or accessories, search by model on Sears PartsDirect.
Last updated: February 2026
How to unlock a Craftsman miter saw?
To unlock a Craftsman miter saw like model 137212060, you typically release the cutting head lock pin (for raising the head) and then unlock the miter table and/or bevel lock handle depending on what you’re trying to adjust. The exact lock locations and names are shown in the owner's manual.
Use this when the saw is stored with the head locked down.
- Unplug the saw.
- Push down slightly on the cutting head to take pressure off the lock.
- Pull the lock pin out.
- Let the cutting head rise to the uppermost position.
| Lock type | What it controls | When you use it |
|---|---|---|
| Lock pin (cutting head lock) | Holds the cutting head down for storage/transport | Before moving or storing the saw |
If the table will not rotate, the miter lock is still engaged.
- Lift up on the Quick-Cam miter table lock to unlock the table.
- If you’re setting a common angle, raise the positive stop locking lever, rotate to the angle, then release the lever so it snaps into a positive stop.
- Press down on the Quick-Cam miter table lock to lock the angle when you’re done.
If the head will not tilt left or right, the bevel lock is still engaged.
- Loosen the bevel lock handle.
- Tilt the cutting head to the desired bevel angle using the bevel scale as a guide.
- Tighten the bevel lock handle to secure the bevel setting.
Using the correct lock for the adjustment prevents the saw from shifting during a cut. A locked miter table or bevel setting helps keep your angle accurate and reduces the chance of binding or kickback.
If a lock lever, handle, or pin is sticking, bent, or missing, use the model 137212060 parts diagrams to identify the correct replacement; you can also search by model number on Sears PartsDirect.
Last updated: February 2026
Does Craftsman make a double bevel miter saw?
Yes. Craftsman makes dual (double) bevel miter saws in some product lines; however, the Craftsman 137212060 covered here is a sliding compound miter saw with a bevel scale, and you make “both-direction” bevel results by repositioning or flipping the workpiece rather than tilting the head right.
A double bevel (dual bevel) miter saw tilts the blade left and right for bevel cuts, so you can cut matching angles without flipping the board.
- Single bevel: head tilts one direction; you flip or rotate the workpiece for mirrored bevels
- Dual bevel: head tilts left and right; faster for repeated trim work
- Compound miter: combines miter and bevel for crown molding and complex angles
Use the bevel scale and bevel locking handle described in the 137212060 owner's manual to confirm how the head tilts and where it locks.
- Unplug the saw before checking movement
- Locate the bevel scale and bevel locking handle
- Loosen the bevel lock and tilt the head through its available bevel range
- Re-tighten the lock and confirm the head holds position without play
- For opposite-direction bevels, plan to flip or reposition the workpiece
| Feature | What the saw head does | What you do for mirrored bevels |
|---|---|---|
| Single bevel (like 137212060) | Tilts one direction | Flip or rotate the workpiece |
| Dual bevel | Tilts left and right | Keep the workpiece in place |
If you cut a lot of crown molding, baseboards, or casing, dual bevel saves time and reduces handling errors. For occasional projects, a single bevel sliding compound saw still delivers accurate miter and bevel cuts with the right setup.
For model-specific diagrams and to look up replacement parts by model number, use the parts list for 137212060 or search by model on Sears PartsDirect.
Last updated: February 2026