Craftsman 706139910 tool chest Parts

On a Craftsman tool chest like model 706139910, the model number is typically on an identification label or stamp on the cabinet body, not on a drawer. Check the back panel first, then the inside frame near the drawer openings; confirm the exact format in the owner's manual.

Look in these spots in order (they are the most common and easiest to access):

• Back panel: a sticker label or a number stamped into the metal
• Inside the cabinet frame: vertical support near the drawer openings
• Side panel or end brace: often near the lower rear corner
• Inside the top lid area (if your unit has a top compartment)
• Near the lock area: around the door or lock cutout on units with a door

1. Pull the chest 6 to 12 inches away from the wall.
2. Use a flashlight and scan the upper and lower back panel for a label.
3. If you do not see a label, look for a stamped number along seams, braces, or vertical supports.
4. Write down everything you see (letters, dashes, and spaces) before searching.

We use the model number to match the correct drawer slides, rails, lock parts, and hardware. Even similar-looking Craftsman tool chests can use different drawer assemblies and fasteners, so the exact model number prevents ordering the wrong parts.

Last updated: February 2026

Yes. On the Craftsman tool chest model 706139910, you can remove the drawers by fully extending each drawer, releasing the slide stops on both sides, and then pulling the drawer out. This is useful for cleaning, lubricating slides, or reducing weight before moving the chest.

• Fully extend the drawer.
• Push the drawer back in slightly (about 1/8 inch).
• Insert a flat screwdriver into the slot in the slide.
• Depress the stop until it clears the latch (do this on both slides).
• Pull the drawer straight out while holding both stops released.
• Set the drawer on a flat surface to avoid bending the slides.

• Pull the slide stop outward to engage the latch (typically about 3/16 to 1/4 inch).
• Set the drawer onto both slides evenly.
• Push the drawer in until the stops snap past the latches.
• Open and close the drawer a few times to confirm smooth travel.

The manual calls out tip-over risk when drawers are open. Before moving the chest:

• Close and latch all drawers.
• Move one drawer at a time if you are removing multiple drawers.
• Keep the load low and centered (heavy tools in lower drawers).
• Avoid rolling over cords, thresholds, or debris.
• Do not move the unit on a truck bed or other moving object.

Drawer slides can bind or get damaged if the stops are forced. Removing drawers the right way protects the slide latches, keeps drawers aligned, and makes the tool chest easier and safer to handle.

For the exact slide-stop location and drawer handling notes for model 706139910, use the owner's manual.

Last updated: February 2026

Yes, some Craftsman tool boxes are made in China, and some are made in other countries. For Craftsman tool chest model 706139910, the country-of-origin statement shown in the owner's manual is “Made in the U.S.A.”

The documentation for this specific Craftsman stationary storage unit includes a country-of-origin line. Use that plus the product label to confirm you have the same unit.

• Match the model number on your label to 706139910
• Look for a “Made in …” marking on the cabinet (often inside a drawer area or on the back)
• Keep the manual with the unit for future parts and assembly reference
• Avoid relying on brand-wide statements; Craftsman sourcing varies by product line

Country-of-origin markings are typically found on the unit itself, not just on packaging.

Manufacturing location can affect small details like hardware type, drawer slide fit, and which service parts match your exact build. Confirming the model number and origin marking helps prevent ordering the wrong replacement parts.

Last updated: February 2026

We don’t provide instructions for bypassing the lock on a Craftsman tool chest like model 706139910 using a paperclip. The reliable way to regain access is to use the correct key or service the lock and door alignment using the procedures in the 706139910 owner's manual.

• Remove pressure on the latch: gently push the door or drawer front inward while turning the key.
• Check for binding: a slightly racked cabinet or overloaded drawer can twist the frame and pinch the lock.
• Verify drawers are fully closed; a drawer that is out of square can interfere with the lock cam.
• Inspect the door catch area for bent metal or debris.
• Use a small amount of dry lubricant (graphite or a lock-safe spray) in the keyway; avoid oil that attracts grit.

The 706139910 manual covers lock assembly details such as inserting the lock (with the locking cam vertical), seating the retaining clip, and removing the lock by driving out the retaining clip. Follow the lock assembly section in the manual so the cam and catch align correctly.

Paperclip picking can deform the cylinder and cam, turning a simple access problem into a lock replacement. Using the manual’s lock and alignment procedures protects the door, catch, and security of your tool chest.

Last updated: February 2026

Some Craftsman toolboxes and tool chests are sold with a lifetime warranty, but it is not universal; the exact coverage depends on the specific product’s written warranty terms and how the storage unit is used. For Craftsman model 706139910, confirm the warranty terms and use limits in the 706139910 owner's manual.

Most tool storage warranties focus on defects in materials or workmanship under normal household use, not damage from misuse or exceeding stated limits.

Common items that are typically excluded:

• Overloading drawers or the top surface
• Tip-over incidents (for example, opening multiple drawers at once)
• Damage during moving or transport
• Modifications (added equipment, drilled holes, welded parts)
• Abuse, neglect, or improper assembly

The 706139910 manual includes safety rules and operating instructions that help you stay within “normal use” expectations.

We recommend following these manual-based practices:

• Open drawers carefully; avoid creating an unstable, tip-prone condition
• Close drawers and doors before moving the unit
• Do not mount the unit on a moving platform (such as a truck bed)
• Do not alter the cabinet or add equipment that changes how it’s used

Use this checklist so you are matching the warranty to the correct product:

• Match the model label on the cabinet to 706139910
• Review the warranty and safety sections in the 706139910 owner's manual
• Keep your proof of purchase with the manual
• If you need help interpreting coverage, contact Sears PartsDirect support

Warranty coverage is tied to the written terms and “normal use.” Using the tool chest within the manual’s safety and loading guidance helps prevent slide, drawer, and cabinet damage that warranties commonly exclude.

Last updated: February 2026