Name: Lawn & Garden Equipment Engine Deni 165SB Carburetor Kit 951-12712
Brand: MTD, Craftsman
Price: 53.53 USD
Availability: InStock
Rating: 2 (6 reviews)

Online Price

$53.53

36% OFF Was : $83.20

In Stock

Qty

Zip Codes Near

60169

Edit

Return Policy

60-day return policy

Learn more

Shipping

If you place your order today, your part(s) will arrive by:

Confirm this part fits

Previous part numbers

Part #951-11020A

Part #951-11020

Part #751-11020

This Part Also Fits

MTD Craftsman

Part Information

Special details: Before ordering carburetor rebuild kit 951-12712, please read the detailed information below to ensure the kit will work with the calibration code on your carburetor.

This carburetor rebuild kit (part number 951-12712) is for lawn and garden equipment engines.

Carburetor rebuild kit 951-12712 contains the parts needed to rebuild Deni carburetors with calibration code 165SB. If your original carburetor doesn't match the supplier and/or code, use this chart to find the correct part number.

The carburetor supplier name (Huayi or Deni) is stamped into the carburetor body, usually opposite the fuel inlet. The calibration code is the center series of numbers printed on the carburetor (starting with the 8th digit), and is sometimes also stamped into the carburetor body.

Let the engine cool and drain the fuel tank before installing this part. Work in a well-ventilated area and wear work gloves to protect your hands.

$129.24

8% OFF Phone Price : $141.24

$25.42

19% OFF Phone Price : $31.42

$89.42

6% OFF Phone Price : $95.42

$76.40

7% OFF Phone Price : $82.40

$23.84

20% OFF Phone Price : $29.84

Sort by

Filter by

0 Reviews

Not quite right

January 20, 2019|Markedman, Missouri

The float provided in this kit which was listed to fit this particular model snowblower did not fit. the flange that the pin goes through was slightly too wide to fit between the posts. I could have ground it down to fit but the old float was still good so used it instead. All othe parts fit correctly. Easy to install after watching YouTube videos. Snowblower started on first try after reassembly.

Ease of InstallationEasy

Duration of Installation30 minutes - 1 hour

verified customer

Was this review helpful?

Yes No

Craftsman 24 in. Snow Thrower Model 247.889571

January 20, 2019|Gene76, St. Peters, MO

Used Carburetor Kit-substitution 951-12712 instead of Part No. 951-11020A from Sears. Had to use original white plastic float instead or new float because new float was tight in carburetor bowl. No gaskets came with carb. kit, except the bowl gasket. Reinstall carburetor in snow thrower and put all parts back together and started snow thrower on first pull. Unit runs rough, but will work.

Ease of InstallationModerate

Duration of Installation1 - 2 hours

verified customer

Was this review helpful?

Yes No

Not exaclly the same parts

September 10, 2018|slrinmd, Baltimore

How the needle fit in the float was not the same as the original equipment. While the provided parts probably would have worked, no instructions were provided how to assemble the very tiny, but complex and essential parts. Decided to re-install the original float and needle since they seemed to be in good shape.

Ease of InstallationModerate

Duration of Installation30 minutes - 1 hour

verified customer

Was this review helpful?

Yes No

Float did not fit.

January 15, 2019|ELars, MN

The original float uses an integral plastic tab for the hinge portion. This tab fits between two cast metal 'horns' on the carb and is held in place by a metal hinge pin. The supplied float uses a metal tab instead, however it was too wide (by a mm or two) to fit between the horns. As such, it was not a suitable substitute for the original part, and did not correct the problem.

Ease of InstallationVery Difficult

Duration of InstallationMore than 2 hours

verified customer

Was this review helpful?

Yes No

Irrelevant parts

December 10, 2018|DYI D, Detroit

These carbs are not rebuildable since the gasoline corroded the one year old carburetor.

Ease of InstallationModerate

Duration of Installation1 - 2 hours

verified customer

Was this review helpful?

Yes No

Wrong part

November 29, 2018|crusty61, NY

I paid 40.00 for this part and what a joke. Spent the time taking the carburetor apart only to find out they were the wrong parts! Float wouldn't fit and the needle valve was way to short. No new gaskets for the rebuild. I suppose sears wanted 40.00 more for the gaskets This is the second time you did this to me and it's the last.

Ease of InstallationVery Difficult

Duration of InstallationMore than 2 hours

verified customer

Was this review helpful?

Yes No

Average Customer Ratings

Overall 2.0 stars