Get free shipping on your order, with any water filter subscription. Find my filter

Open Hamburger Menu
Sears Parts Direct
Tips to find your model number

KitchenAid KSB4028BM0 blender Parts

Here are the diagrams and repair parts for KitchenAid KSB4028BM0 blender, as well as links to manuals and error code tables, if available.

KitchenAid KSB4028BM0 blender
By Schematic
By Part
SELECT DIAGRAM
?

This is the number corresponding to the part on the diagram / schematic

Browse Parts for KSB4028BM0 BLENDER

KitchenAid BLENDER KSB4028BM0 FAQs

A KitchenAid blender like model KSB4028BM0 usually leaks when the jar assembly is not sealing tightly, the jar is cracked, or the drive area is letting liquid migrate downward. In most cases, correcting jar seating and replacing the worn jar-related component stops the leak.

Quick checks that fix most leaks

  • Unplug the blender and remove the jar.
  • Inspect the jar for hairline cracks, especially near the bottom and around the blade area.
  • Re-seat the jar fully on the base; a jar that is slightly off-center can drip.
  • Confirm the lid is installed correctly; overfilling can force liquid out at the lid.
  • Clean and dry all mating surfaces (jar bottom and base top) so the jar sits flat.

Where the leak is coming from (symptom guide)

What you see Most likely cause What to do next
Drips from the bottom of the jar Jar assembly wear or damage Replace the jar assembly W11433178
Liquid appears around the drive area on the base Coupling area worn or not fitting tightly Inspect and replace the blender drive coupling W11627528 if rounded or loose
Leak only when blending hot liquids or very full jar Overfill, steam pressure, or lid not seated Fill less, vent per recipe, confirm lid fit

Parts that commonly solve leaking on KSB4028BM0

If cleaning and re-seating do not stop the leak, these are the most common replacements for this model:

Why it matters

Leaks can let liquid reach the drive coupling and motor area, which leads to slipping, unusual noise, and premature wear. Stopping the leak early protects the electronic control and motor.

Last updated: February 2026

Yes. For your KitchenAid KSB4028BM0 blender, replacement parts are sold for common wear items and assemblies (like the jar, lid, and drive components) so you can restore blending performance instead of replacing the whole unit.

Common KSB4028BM0 replacement parts we see customers need

These are typical fixes when a blender leaks, won’t blend smoothly, or the jar won’t drive correctly:

How to choose the right part (quick checklist)

Use this checklist to avoid ordering the wrong KitchenAid blender part:

  • Match the model number exactly: KSB4028BM0
  • Confirm the symptom (leak, no power, slipping drive, cracked jar)
  • Compare the part name and part ID to what you’re replacing
  • Check whether you need an assembly (jar, lid) versus a small component (coupler, screw)
  • Inspect for visible wear: stripped coupling teeth, cracks, burning smell, loose connections

Quick part guide by symptom

Symptom Most likely area Part to check first
Jar leaks or is cracked Jar/lid sealing surfaces Jar assembly, lid assembly
Blades don’t spin but motor runs Drive interface Blender drive coupling
No response from controls User interface/control board Electronic control
Loud hum, stalls under load Motor/drive train Motor

Why it matters

Replacing the correct KitchenAid KSB4028BM0 blender part restores safe operation and consistent blending results, and it prevents secondary damage (for example, a slipping coupling can wear faster and strain the motor).

Last updated: February 2026

To disassemble the blade area on your KitchenAid KSB4028BM0 blender, unplug the blender first, then remove the jar and work from the underside of the jar. Many KitchenAid-style jar bases use a reverse-thread retaining nut, so loosening can require turning clockwise.

Safety first (sharp blade and pinch points)

  • Unplug the blender base before you start.
  • Wear cut-resistant gloves; the blade edges stay sharp even when dull.
  • Work on a towel to keep the jar from slipping.
  • Never grip the blade from the inside of the jar while loosening hardware underneath.
  • If anything is cracked or stripped, stop and replace the damaged part.

Step-by-step: typical jar blade removal

  1. Remove the jar from the motor base and empty it.
  2. Turn the jar upside down and locate the retaining nut or “wing nut” style fastener on the bottom.
  3. Hold the blade assembly steady (from the bottom side) and loosen the retaining nut.
  4. If the nut is reverse-threaded, loosen by turning clockwise (opposite of normal).
  5. Lift off the base components and carefully remove the blade assembly and seals.

Which direction do I turn it?

Many KitchenAid blender jar assemblies use reverse threads to help prevent the nut from loosening during operation.

What you see under the jar Most common thread style “Loosen” direction
Wing nut / retaining nut on blade shaft Reverse-thread Clockwise
Standard hex nut (less common) Standard thread Counterclockwise

When to replace parts instead of disassembling

If you have leaking, wobble, or grinding, replacement is often faster and more reliable than rebuilding the jar.

  • Persistent leaks around the blade seal
  • Blade wobble or a stripped retaining nut
  • Cracked jar base or damaged threads
  • Coupler slipping or loud rattling at the drive point

For KSB4028BM0, common replacements include the jar assembly W11433178 and the blender drive coupling W11627528.

Why it matters

Correct disassembly prevents stripped threads, broken seals, and injuries. Reverse-thread hardware is the most common reason customers overtighten or damage the retaining nut during blade removal.

Last updated: February 2026

On the KitchenAid KSB4028BM0 blender, the drive coupling is typically a threaded part on the motor shaft; removal usually means holding the shaft steady and turning the coupling in the loosening direction until it unthreads. If it is stuck, use controlled force so you do not crack the base.

Before you start (safety and setup)

  • Unplug the blender and remove the jar.
  • Work on a stable counter with good lighting.
  • Protect the housing with a towel to prevent scratches.
  • Use gloves for grip; avoid grabbing the coupling with bare hands if it is sharp or damaged.
  • If the coupling is melted or seized, stop and plan on replacing it.

How we remove the drive coupling

  1. Access the coupling: With the jar off, locate the coupling on top of the base.
  2. Hold the motor shaft: If you can access the shaft from below (varies by design), hold it steady while turning the coupling.
  3. Unthread the coupling: Turn the coupling in the loosening direction until it comes off.
  4. If it is stuck: Apply a few sharp, controlled taps to the coupling (not the housing) to help break it free, then try again.

Tools that help

Tool What we use it for Notes
Strap wrench Gripping without chewing up plastic Best for tight couplings
Small hammer Light taps to free a seized coupling Tap gently, avoid the base
Screwdriver set Base access (if needed) Keep screws organized

When to replace the part instead of reusing it

Replace the coupling if you see any of the following:

  • Rounded or stripped drive teeth
  • Cracks, wobble, or melted plastic
  • Burning smell or black dust around the coupling
  • Jar slips even though the motor runs

For the correct replacement on this model, use the blender drive coupling W11627528.

Why it matters

A worn drive coupling is designed to fail first to protect the motor and jar drive system. Replacing it restores proper power transfer and helps prevent damage to the motor, electronic control, and jar assembly.

Last updated: February 2026

Yes, you can dishwasher-clean some removable parts on your KitchenAid KSB4028BM0 blender, but we recommend hand-washing the motor base and any parts with electrical or drive components. For best results, wash the jar and lid promptly after use to prevent residue from drying on.

What you can and cannot put in the dishwasher

In most KitchenAid blenders like the KSB4028BM0, the safe approach is to dishwasher-clean only the non-electrical, removable pieces.

  • Dishwasher (typical): jar, lid, and non-electrical inserts
  • Hand-wash only: motor base, power cord, control area
  • Avoid dishwasher: parts that couple to the drive system if they show wear or trap water

Quick cleaning method (no dishwasher needed)

This is the fastest way to clean the jar after smoothies, sauces, or shakes.

  • Fill the jar halfway with warm water
  • Add 1 to 2 drops of dish soap
  • Run on a low speed for 10 to 20 seconds
  • Rinse thoroughly
  • Air-dry with the lid off

Parts to check if cleaning issues keep happening

If you notice leaking, wobbling, loud grinding, or the jar not engaging smoothly after washing, inspect these common wear items.

Symptom What it often points to Example part for this model
Jar won’t seat or slips Worn drive interface Blender drive coupling W11627528
Persistent odor or cloudy jar Jar wear or residue buildup Jar assembly W11433178
Lid no longer seals well Warped or worn lid Lid assembly W11752211

Why it matters

Dishwasher heat and strong detergents can shorten the life of seals and plastic over time. Using the quick-clean method and keeping the motor base dry helps prevent drive wear, corrosion, and premature part replacement.

Last updated: February 2026

KitchenAid does not assign a “color of the year” to the KitchenAid KSB4028BM0 blender model itself. This model is sold in multiple finishes; the correct way to identify your blender’s color is to match the finish name to the color-specific housing parts used on your unit.

How to identify your KSB4028BM0 finish

Use the blender’s physical finish and any label information to match the correct color family.

  • Check the model/serial label (commonly on the underside of the base) for any color or variant code
  • Compare the visible top housing color to the color-specific “upper base” options
  • If the blender has been repaired, confirm the upper base color matches the rest of the housing
  • When ordering cosmetic parts, match the exact color name (matte black, white, etc.)

Color-specific parts you can match to your blender

These parts change the visible exterior finish; choosing the right one prevents a mismatched look.

Part (color) What it is Best used for
Upper base (matte black) W11287120 Color top housing Scratches, cracks, cosmetic refresh
Upper base (white) W11287121 Color top housing Yellowing, damage, cosmetic refresh
Upper base (passion red) W11245953 Color top housing Broken tabs, cosmetic replacement

Why it matters

On KitchenAid blenders, cosmetic housing pieces are finish-specific. Ordering the correct upper base color keeps your KSB4028BM0 looking uniform after a repair, even when the blender runs perfectly.

Last updated: February 2026

Repair guides for bottom-mount refrigerators

How to replace an electronic control board on the back of a refrigerator

How to replace an electronic control board on the back of a refrigerator

If your refrigerator isn't running, an electronic control board failure could be the problem. A service technician can d…

Repair time and Difficulty

 15 minutes or less
How to replace a door gasket in a French-door refrigerator

How to replace a door gasket in a French-door refrigerator

The door gasket, often called a door seal, seals the gap around the door to keep the cold air in and the warm air out. R…

Repair time and Difficulty

 15 minutes or less
How to replace an in-door ice maker on a French door refrigerator

How to replace an in-door ice maker on a French door refrigerator

Follow these step-by-step instructions how to replace the in-door ice maker in Kenmore TRIO and LG French door refrigera…

Repair time and Difficulty

 15 minutes or less

Articles and videos for bottom-mount refrigerators

How to Replace the Water Filter in a Maytag Refrigerator

How to Replace the Water Filter in a Maytag Refrigerator

No matter what style Maytag refrigerator you have, we can walk you through replacing the water filter.…

Are DIY appliance repairs safe?

Are DIY appliance repairs safe?

Find out how to stay safe when repairing your appliances.…

How to disassemble the ice and water dispenser on a GE refrigerator

How to disassemble the ice and water dispenser on a GE refrigerator

See how to disassemble the dispenser on common GE refrigerators.…

Parts & More

Dishwasher
Fitness & Exercise
Gas Walk-Behind Mower
Parts
Repair
Side-By-Side Refrigerator
Top-Mount Refrigerator