Kenmore 79047853400 wall oven/microwave combo Parts

To reset the microwave controls on your Kenmore 79047853400 wall oven/microwave combo, use Stop/Clear to cancel cooking or erase a wrong entry. After a power interruption, press Stop/Clear and set the clock again using the steps in the owner's manual.

Quick reset options (keypad reset)

• Clear a programming mistake: Press Stop/Clear once, then re-enter settings.
• Stop cooking temporarily: Press Stop/Clear once.
• Cancel a program during cooking: Press Stop/Clear twice.
• After a power outage: Press Stop/Clear, then reset the clock.

If the display shows “ENJOY YOUR OVEN PRESS CLEAR AND PRESS CLOCK”

That message appears when power is restored and the clock needs to be set.

1. Close the door.
2. Press Stop/Clear.
3. Press Clock, enter the time, then press Clock again to save.

Related features that can look like a “reset” problem

If the keypad seems unresponsive or the oven will not run as expected, these settings commonly cause it.

Symptom	What to check	What to do
Keypad appears locked	Child lock	Use the Help feature steps in the owner's manual to turn Child Lock on or off
Unit runs but does not heat	Demonstration mode	Turn Demo mode off using the Demo mode steps in the owner's manual
“ERROR” when setting time	Incorrect clock entry	Press Stop/Clear and re-enter the time

Why it matters

A proper reset clears stored commands and restores normal operation after a power interruption, a canceled cook cycle, or an input error; it also ensures the clock and timed features work correctly.

Last updated: February 2026

To measure a replacement for your Kenmore 79047853400 wall oven/microwave combo, we measure the existing cabinet cutout (not the oven door). Then we compare those numbers to the cutout chart and clearance requirements in the installation guide.

What to measure (cutout, not the appliance face)

Measure in inches, and take each measurement in at least 2 places (top and bottom, left and right) to catch out-of-square cabinets.

• Cutout width: inside left cabinet wall to inside right cabinet wall
• Cutout height: from the cutout floor/support surface to the top of the opening
• Cutout depth: from the front of the cabinet opening to the back wall
• Front clearance: open the door and confirm you have working space in front

Minimum clearances and support to plan for

Your installation instructions call out key requirements that affect fit and safety.

Item to verify	What to look for	Why it matters
Support capacity	Base/support surface must support 225 lb	Prevents sagging and cabinet damage
Front clearance	Allow at least 21 in in front for door depth when open	Prevents door interference and improves access
Level support	Surface must be level side-to-side and front-to-rear	Helps the oven cook evenly and mount correctly
Spacers (if equipped)	Do not remove side/back spacers	Keeps the unit centered and reduces heat buildup

Best practice: compare measurements before you buy

1. Write down your cutout width, height, and depth.
2. Check the cutout dimensions chart for the exact model you plan to install.
3. Confirm electrical requirements and that the unit can be properly grounded.

Why it matters

Wall oven/microwave combos fit a limited range of cutout sizes. Measuring the cabinet opening first helps avoid gaps, binding doors, overheating from poor centering, and costly cabinet modifications.

Last updated: February 2026

Most standard wall ovens are built around 24, 27, or 30 inches wide. For your Kenmore 79047853400 wall oven/microwave combo, the exact cabinet cutout and clearance requirements are listed in the installation guide, and those measurements matter more than “standard” sizing when you are fitting it into existing cabinetry.

Common “standard” wall oven size ranges

These are typical ranges you will see across many electric wall ovens and wall oven combos:

• Width: 24, 27, or 30 inches (most common)
• Cabinet cutout depth: often about 22 to 24 inches
• Overall depth (including door/handle): often closer to 25 to 27 inches
• Single-oven cutout height: commonly 27 to 29 inches (combination units are taller)

What to measure before you buy or install

Use a tape measure and compare your numbers to the cutout chart in the installation guide. Focus on:

• Cutout width, height, and depth (inside the cabinet opening)
• Front clearance for the door swing (many installs need about 21 inches of clear space in front)
• Support strength of the cabinet base (many wall oven combos require a sturdy platform)
• Junction box location and slack in the electrical cable

Quick reference: “standard” vs. what matters for fit

Item	“Standard” expectation	What determines fit for 79047853400
Width	24, 27, 30 inches	Your cabinet cutout width and trim overlap
Depth	22 to 24 inch cutout	Cutout depth plus door/handle projection
Height	Varies by single vs. combo	Combination cutout height from the install specs

Why it matters

A wall oven can be “standard width” and still not fit if the cutout height/depth, front clearance, or support platform is off. Using the model-specific cutout chart helps prevent cabinet rework and door clearance problems.

Last updated: February 2026