CONFIRM THE PART FITS

Washer Agitator (replaces 131605900) 131605901

5 Stars
2
4 Stars
0
3 Stars
3
2 Stars
0
1 Stars
4

Part #131605901

Online Only Price
$120.66
8% OFF Phone Price : $130.66
In Stock
For ZIP codes near Edit

Part Information

This agitator (part number 131605901) is for washers.

Agitator 131605901 rotates back and forth to move the clothes inside the tub to clean the load.

Unplug the washer before installing this part. Wear work gloves to protect your hands.

Reviews

They dont make them like they used to.
March 08, 2022

I purchased a replacement because two of the flexible flaps on the end of the agitator arm came off on my ten year old unit. All of the flappers on the replacement unit broke off within 45 days. I ordered a second replacement, I'm hoping for a better outcome.

C. D L, Vista CA 92083

Did you find this review helpful?

Ease of Installation
Moderate
Duration of Installation
30 minutes - 1 hour
Arrived broken
March 07, 2021

Part arrived broken and unusable. I will be exchanging it and we can try this fiasco all over again.

Photo 1

Redbeard66, CT

Did you find this review helpful?

Ease of Installation
Very Easy
Duration of Installation
Less than 30 minutes

Yes, I would recommend this to a friend

product quality
May 31, 2020

original agitator around 12 years old. Seemed odd that 2 "wings" broke off the agitator. Loads were never heavy and were always done on light. Got the replacement and was delver as promised. It do not last 3 loads [again all light loads]. 3 broke off on the same load. It seems obvious to me that the phone agent is used to such issues and sent a replacement without delay. I half expected some trouble with the return but there was none. It has worked well for a few weeks now.

Mr. M, Undisclosed

Did you find this review helpful?

Ease of Installation
Easy
Duration of Installation
30 minutes - 1 hour
Old to new agitator
February 05, 2020

After removing the old agitator found rust scale had built up on shaft. After removing with wire wheel, cleaned agitator installed.

JefferyC2745, Charleston SC

Did you find this review helpful?

Ease of Installation
Easy
Duration of Installation
30 minutes - 1 hour

Yes, I would recommend this to a friend

Build quality?
September 04, 2018

Molded parts are all good, attached ring was not attached well, lots of excess material used, did not hold. Part works fine. Arrived quickly, no padding at all. Only place I found this part.

Tampaman, Tampa

Did you find this review helpful?

Ease of Installation
Easy
Duration of Installation
Less than 30 minutes
Defective part
July 01, 2018

I could not install. The part was defective. Fortunately the part was easy to remove, easy to replace if I had a quality part.

ToddC, Dallas, GA

Did you find this review helpful?

Ease of Installation
Easy
Duration of Installation
30 minutes - 1 hour
Fit/works as it should
April 30, 2018

The spindle this part was being attached to had somewhat corroded over the years. My solution was to wirebrush the spindle in order for the agitator to be slid into place without too much resistance. Also be sure to keep the pieces from the old agitator that hold the fabric softener, unless ordering those parts as well. The toughest task was cleaning the tub area after removing the old agitator, a wet/dry vac (use crevice tool) and an old toothbrush helps. Be careful cleaning this section, as there are screens that filter the water as it drains...i found four pennies buried in the gunk in mine. See pic for tub area after gunk cleanup.

The black oblongs are 16 somewhat delicate screens so be careful when cleaning

BDavidR, Nesconset, NY

3 people thought this review was helpful.

Ease of Installation
Moderate
Duration of Installation
30 minutes - 1 hour
Pretty easy job!
April 24, 2018

Pop the fabric softener dispenser off the top (just pull up with hands) Need pump pliers to pull the tab and a circular plastic cover with rubber o-ring with pop out (this will take some effort, depending on how old your machine is) Probably going to need a 1/2 socket with at least 3" extension -- hold base of agitator to loosen. Clean and lube the metal spline (a little soap will do the trick) to help slide the new agitator on. Revere other steps.

sid7hartha, Butler, KY

Did you find this review helpful?

Ease of Installation
Easy
Duration of Installation
Less than 30 minutes