Home  >  Bearing

Bearing 137088600


Part #137088600

Replaced by #131777700
Manufacturer substitution
This part replaces 137088600. Substitute parts can look different from the original.
Online Only Price
$59.16 | 
8% OFF 
Phone Price: $64.16
In Stock
For ZIP codes near Edit
60-day return policy

Part Information

This drum support shaft (part number 131777700) is for dryers.

Drum support shaft 131777700 supports the drum at the dryer's back wall while allowing the drum to spin.

Unplug the dryer before installing this part. Wear work gloves to protect your hands.

Top models using the same part

Model NameModel NumberDiagram Name
Model #FLEB8200FS1 Frigidaire laundry centerFLEB8200FS1
Upper cabinet/drum heater
Model #GLGT1142FS2 Frigidaire laundry centerGLGT1142FS2
Upper cabinet/drum heater
Model #WGR242AS5 White-Westinghouse dryerWGR242AS5
Model #SWXG831HQ4 White-Westinghouse laundry centerSWXG831HQ4
Upper cabinet/drum heater
Model #SWXG831HS0 White-Westinghouse laundry centerSWXG831HS0
Upper cabinet/drum heater
Model #GLET1031FS2 Frigidaire laundry centerGLET1031FS2
Upper cabinet/drum heater
Model #FGX831FS5 Frigidaire laundry centerFGX831FS5
Upper cabinet/drum heater
Model #CLCE500FW4 Crosley laundry centerCLCE500FW4
Upper cabinet/drum heater
Model #FLGB8200FS2 Frigidaire laundry centerFLGB8200FS2
Upper cabinet/drum heater
Model #FLEB8200FS2 Frigidaire laundry centerFLEB8200FS2
Upper cabinet/drum heater


Patchogue NYReviews 1Votes 0
• 2 years ago
JimD• 2 years ago
Just what i needed

Ordered this for my stacked washer and dryer. this part was exactly like the one on my dryer that broke. You need two people to do this job. I removed the top and front and disconnected the belt through the access panel on the rear. took about 2 hours but saved a few hundred dollars having someone do it for us.

Response from Sears PartsDirect:
CS OFFLINE • 2 years ago

We are so thrilled you had a 5-star experience. Thank you for taking the time to leave us a rating. We thank you for choosing Sears Parts Direct for your part needs!

Wheatland, WYReviews 1Votes 0
• 2 years ago
Rotho• 2 years ago
Very easy installation

Easy to install, hardest part was taking the dryer apart. I did not have instructions so removed a few pieces that were not necessary. But all-in-all the whole process was easy and saved me a lot of money.

Dub T
Cedarville, MIReviews 1Votes 0
• 2 years ago
Dub T• 2 years ago
Dryer work again!

Took dryer apart, ordered the obviously broken parts, put back together in short order, and it works fine.

MichiganReviews 1Votes 0
• 3 years ago
Magnummike• 3 years ago
Bearing and shaft for Kenmore drier

Easy installation one note I was able to install without accessing rear panel to take belt off of tension pulley. Killed circuit breaker then from front pulled back on pulley arm and removed belt this allowed me to fix without pulling washer/drier out from right corner!

Green Bay, WIReviews 1Votes 0
• 4 years ago
pj19• 4 years ago
old one wore completely through

I wasn't sure what the part was supposed to look like. The one I removed from the dryer was worn and broken into two pieces. I replaced both the dryer shaft and the bearing, and now the dryer runs and is much quieter. I didn't need to removing the top of the dryer to disassemble, but found that I had to remove the top to put the drum back in. I also struggled removing the control panel and reinstalling the belt. There is an access panel on the back which makes the belt install easier.

Maryville, TennesseeReviews 1Votes 0
• 4 years ago
Linda65• 4 years ago
Not easy to install, but not extremely difficult.

My Kenmore dryer is 15 yrs old. It needed several parts that started with a belt. After getting into it, hubby discovered it needed more than a belt. I ordered the parts, and they arrived quickly. We needed one more part, but I couldn't find it on website. I called customer service, and the very nice young man found the part and shipped it. We are very satisfied with the whole experience. Thank you Sears!

Andrew P.
Reviews 1Votes 0
• 5 years ago
Andrew P.• 5 years ago
Second times a charm

Went smoothly running better then it has in years. Definitely need a second person to hold the assembly on the back of the unit while you put the bearing assembly on back of dryer. If you're doing it by yourself a magnet from the back side holds the bearing in place pretty good

Reviews 1Votes 0
• 5 years ago
Jose97• 5 years ago
good and on timw

i had previous experience, so there was no problem installing it