How to Replace a Snowblower Fuel Line

 

file

This step-by-step repair guide shows how to replace the fuel line on a snowblower. The fuel line carries fuel from the gas tank to the engine. If the fuel line is cracked or damaged, fuel won't flow to the carburetor to start the engine. Replace a damaged or cracked fuel line with the manufacturer-approved replacement part.

Repair difficulty:
     
Time required:

Less than 30 min.

Parts Required

  • Fuel line

For manuals, repair guides, and specific part recommendations, enter your model number.

Tools Required

  • Work gloves
  • Phillips screwdriver
  • Slot screwdriver
  • Needle-nose pliers
  • Wrench set
  • Socket and ratchet set

Before you begin

Siphon out the gas or run the snowblower until the tank is empty. Allow the engine to cool.

Position the snowblower in a well-ventilated area. Wear work gloves to protect your hands.

Instructions

 Warning: Undertaking repairs or maintenance to appliances or power equipment can be hazardous. Should you choose to undertake repairs or maintenance, you are assuming the risk of injury to your person or property. In an effort to reduce the risk, use the proper tools and safety equipment noted in the applicable guide and follow all instructions. Do not proceed until you are confident that you understand all of the steps and are capable of completing the repair. Some repairs or maintenance, however, should only be performed by a qualified technician.

How to Replace a Fuel Line

Step 1: Disconnect the spark plug wire

Pull the spark plug wire up and off the plug.

Step 2: Remove the electric starter switch

Remove the mounting screws and pull the starter switch off the bracket.

 

Let the starter switch hang by the electrical cord.

Step 3: Remove the engine shroud

Remove the key.

 

Pull off the choke and throttle knobs.

 

Remove the acorn nuts that secure the carburetor to the engine.

 

Remove the muffler shroud mounting screws.

 

Work the engine shroud off the carburetor mounting studs, leaving the primer hose and breather hose connected.

Step 4: Remove the fuel line

Release the fuel line clamp and pull the fuel line off the fuel filter.

 

Repeat the process to release the other end of the fuel line from the carburetor and remove the fuel line.

Step 5: Install the new fuel line

Connect the new fuel line on the tank and secure it with the fuel line clamp.

 

Repeat the process to connect the other end of the new fuel line to the carburetor.

Step 6: Reinstall the engine shroud

 Tip: Removing the muffler shroud is necessary because the engine shroud fits under the bottom liip of the muffler shroud. You can remove the engine shroud without removing the muffler shroud but the muffler shroud must be removed for reassembly.

Pull off the muffler shroud before reinstalling the engine shroud.

 

Remove the belt cover mounting bolts and pull off the belt cover.

 

Remove the bolts from the red chute support bracket and pull the support bracket forward, releasing the control rod from the 4-way control rod receiver.

 

Remove the front muffler shroud mounting bolts.

 

Release the wire control cables from the retainer clip and pull off the muffler shroud.

 

Align the choke knob shaft and the 2 carburetor mounting posts with the openings on the engine shroud and work the engine shroud onto the engine. Make sure that the breather hose passes through the opening and lines up with the rocker cover breather hose fitting.

 

Slide the breather hose over the rocker cover fitting and secure the hose with the clamp.

 

Reinstall the 2 acorn nuts to secure the engine shroud to the engine.

 

Slide the wire control cables into the retainer clip and position the muffler shroud on the engine.

 

Reinstall the muffler shroud mounting bolts.

 

Push the control rod back into the 4-way control rod receiver and line up the support bracket with the mounting holes.

 

Reinstall the bolts in the red chute support bracket.

 

Reinstall the belt cover using the mounting bolts.

 

Reinstall the choke and throttle knobs.

 

 Tip: Removing the muffler shroud is necessary because the engine shroud fits under the bottom lip of the muffler shroud. You can remove the engine shroud without removing the muffler shroud but the muffler shroud must be removed for reassembly.

Step 7: Reinstall the electric starter switch

Position the electric starter switch on the switch bracket and reinstall the mounting screws.

Step 8: Reconnect the spark plug

Reconnect the spark plug wire.

Step 9: Reinstall the key

Push the key into the slot.