How to Replace a Ground Drive Belt on a Riding Lawn Mower



This DIY riding mower repair guide gives step-by-step instructions for replacing a ground drive belt on a riding lawn mower. The ground drive belt connects the engine crankshaft to the transaxle pulley to drive the rear wheels. If the belt breaks, the lawn tractor won't move. If the belt is worn, the lawn tractor moves sluggishly because the belt slips on the pulley. Examine the ground drive belt and replace it with a manufacturer-approved replacement part if it’s broken or excessively worn.

Use this procedure to replace the ground drive belt on common Craftsman, Toro, Troybilt, Husqvarna, MTD and Ariens lawn tractors and riding mowers.

Repair difficulty:
Time required:

Less than 45 min.

Parts Required

  • Ground drive belt

For manuals, repair guides, and specific part recommendations, enter your model number.

Tools Required

  • Socket wrench set
  • Pliers
  • Nylon rope
  • Torque wrench (optional)
  • Work gloves

Before you begin

Park the tractor on a level surface and set the parking brake.

Let the engine cool.

Wear work gloves to protect your hands.


 Warning: Undertaking repairs or maintenance to appliances or power equipment can be hazardous. Should you choose to undertake repairs or maintenance, you are assuming the risk of injury to your person or property. In an effort to reduce the risk, use the proper tools and safety equipment noted in the applicable guide and follow all instructions. Do not proceed until you are confident that you understand all of the steps and are capable of completing the repair. Some repairs or maintenance, however, should only be performed by a qualified technician.

How to Replace a Ground Drive Belt on a Riding Lawn Mower

Step 1: Disconnect the spark plug

Turn the ignition switch off and remove the key.

Lift the tractor hood and disconnect the spark plug wire.

 Tip: Disconnect both spark plug wires if your tractor has 2 cylinders.

Step 2: Remove the mower deck

Lower the mower deck to its lowest position.

Disengage the cutting blades.

Roll the blade belt off the engine pulley and release the belt from the belt keepers.

Remove the front lift link support retaining pin and washer and then detach the support from the deck.

Remove the left suspension arm retaining clip and washer and then detach the arm from the tractor frame.

Remove the left rear deck bracket retaining clip and washer and then release the bracket from the deck.

Repeat the process on the other side of the deck to disconnect the right suspension arm and right rear deck bracket.

Pull the deck out far enough to access the blade cable attached to the deck.

Release the locking tabs and pull the blade cable out of the deck bracket.

Disconnect the blade cable spring from the idler arm and move the cable aside.

Pull the deck out from under the frame.

 Warning: Because the spring-loaded attachment lift lever exerts more tension on the lever the after you disconnect the rear lift links, don't use the lever until you reinstall the mower deck.

Step 3: Remove the ground drive belt

Remove the flywheel screen cap and position a socket wrench on the flywheel bolt with the wrench handle resting against the fuel tank to keep the crankshaft from turning when you remove the engine pulley bolt.

Remove the engine pulley bolt and washer and then pull the engine pulley off the crankshaft.

Release the drive belt from the pulley.

Release the belt from the idler pulleys and belt guides.

Lift the seat remove the bolt connecting the negative cable to the battery.

Lift the insulating cover and remove the bolt connecting the positive cable to the battery.

Lift the battery out of the battery box.

Release the seat switch wire harness clip from the seat bracket to create slack in the harness.

Release retaining tabs and lift the battery box out of the tractor body.

Set the box on the fender.

Release the drive belt from the transaxle pulley.

Pull out the ground drive belt.

 Tip: You can also keep the crankshaft from turning as you remove the engine pulley bolt by removing the spark plug and then stuffing nylon rope into the engine cylinder.

 Tip: If the old belt is still intact, take a photo of how the belt routes through the idler pulleys so you can route the new belt correctly. If the belt is broken, see the owner's manual for belt routing.

 Tip: Spray a rusted crankshaft bolt with penetrating oil so you can remove it easier.

Step 4: Install the new ground drive belt

Loop the ground drive belt over the transaxle pulley.

Position the battery box in the opening and align the wire harness and battery cables.

Lower the battery box into the tractor body and engage the retaining tabs.

Connect the seat switch wire harness clip to the seat bracket.

With the insulating cover positioned on the cable, connect the positive battery cable to the positive battery terminal.

Connect the negative battery cable to the negative battery terminal.

Lower the seat.

Route the belt through the chassis and over the steering plate.

Push the belt through the inside of the front belt guides.

Loop the belt over the engine pulley, line up the pulley notch with the crankshaft groove and slide the engine pulley onto the crankshaft.

Position the wrench on the flywheel bolt so the wrench handle rests against the fuel tank to prevent crankshaft rotation as you reinstall the engine pulley bolt.

Install the engine pulley bolt and washer.

Remove the wrench from the flywheel bolt and reinstall the flywheel screen cap.

Using your photo as a guide, route the right side of the belt through the front and middle idler pulleys.

Slide the left side of the belt into the belt keeper and over the rear pulley.

Remove the rope from the engine cylinder and reinstall the spark plug.

Step 5: Reinstall the mower deck

Push the deck near the tractor frame.

Connect the blade clutch cable spring to the idler arm.

Push the blade clutch cable retainer into the deck bracket and engage the locking tabs.

Position the deck under the tractor frame.

Reconnect the front lift link support to the deck using the washer and retaining clip.

Reconnect the left suspension arm and deck bracket using the washers and retaining clips.

Repeat the process to reconnect the right suspension arm and deck bracket.

Route the blade belt through the belt keepers and roll the blade belt onto the engine pulley.

Check the blade belt routing on the mower deck and adjust the blade belt if needed to route the belt over all pulleys and through all belt keepers. 

 Tip: See your owner's manual for more on routing the blade belt.

Step 6: Reconnect the spark plug

Reconnect the spark plug wire and lower the tractor hood.

 Tip: Reconnect the spark plug wire and lower the tractor hood.