How to Replace a Riding Lawn Mower Front Tire

 

file

This step-by-step repair guide explains how to change a front tire on a riding lawn mower if the old tire is damaged beyond repair. Replacing the front tire is fairly easy; you just need a few tools and a manufacturer-approved replacement part.

Follow the steps in this repair guide and video to replace the front tire on Craftsman, Husqvarna, Toro, Troybilt, Ariens, Poulan, MTD, Murray, Snapper, Yard-Man, John Deere and Weed Eater riding mowers and lawn tractors.

If you'd rather use tire sealant to repair the tire, the video How to Repair a Riding Lawn Mower Tire shows how.

Repair difficulty:
     
Time required:

Less than 60 min.

Parts Required

  • Front tire

For manuals, repair guides, and specific part recommendations, enter your model number.

Tools Required

  • Floor jack or bottle jack
  • Jack stand
  • Slot screwdrivers
  • Pry bars
  • Pliers
  • Valve stem core removal tool
  • Liquid detergent
  • Water
  • Wood blocks
  • Work gloves
  • Safety goggles
  • Compressed air supply

Before you begin

Park the riding mower on a level surface and set the parking brake.

Let the engine cool.

Wear work gloves to protect your hands and safety goggles to protect your eyes.

 

Instructions

 Warning: Undertaking repairs to appliances can be hazardous. Use the proper tools and safety equipment noted in the guide and follow all instructions. Do not proceed until you are confident that you understand all of the steps and are capable of completing the repair. Some repairs should only be performed by a qualified technician.

How to Replace a Front Tire on a Riding Lawn Mower

Step 1: Disconnect the spark plug

Turn the ignition switch off and remove the key.

Lift the riding lawn mower hood and disconnect the spark plug wire.

Lower the tractor hood.

 Tip: Disconnect both spark plug wires if your engine has 2 cylinders.

Step 2: Jack up the riding mower

Block the rear tires to keep the riding mower from rolling.

Position the jack under the frame and jack up the riding mower to raise the front wheel.

Place a jack stand under the frame to support the riding mower.

Remove the jack.

 

Step 3: Remove the front wheel

Pull off the axle cover.

Remove the retaining ring and then pull off the washers.

Pull the tire off the axle.

Step 4: Remove the tire

Remove the valve stem cap.

Remove the valve stem core, which lets any remaining air out of the tire.

Break the tire bead and pry the tire off the wheel rim on one side.

Pry the tire off the rim on the other side.

Step 5: Install the new tire

Clean the wheel rim.

Set the new tire flat on a work surface.

Lubricate the top tire bead with liquid detergent.

Pry the rim into the top side of the tire.

Flip the rim and tire over.

Lubricate the tire bead with liquid detergent.

Pry the remaining side of the tire onto the rim.

 Warning: Use blunt tools to pry the tire to avoid damaging the new tire bead.

Step 6: Seal the bead

Fill the tire with air to seat the tire bead.

Reinstall the valve stem core.

Fill the tire fully with air.

 Tip: If the tire didn't fill with air, install a ratcheting tension strap around the center of the tire tread and tighten the strap to force the beads outward. Fill the tire with air to seat the tire bead. Carefully release the tension strap and then remove the strap.

 Tip: If the bead doesn’t seal, check the rim and replace it if you find damage.

Step 7: Reinstall the wheel

Slide the wheel on the axle.

Reinstall the washers and snap the retaining ring onto the axle.

Push the axle cover onto the wheel.

Step 8: Lower the riding mower

Push the jack under the frame and raise the riding mower, and then pull out the jack stand.

Lower the riding mower to the ground.

Remove the wood blocks from the rear tires.

Step 9: Reconnect the spark plug

Raise the tractor hood.

Reconnect the spark plug wire and lower the hood.

 Tip: Reconnect both spark plug wires if your engine has 2 cylinders.