How to Rebuild a Riding Lawn Mower Carburetor

 

file

This DIY riding mower repair guide gives step-by-step instructions for rebuilding the carburetor on a riding lawn mower. The carburetor blends air and fuel to produce a combustible mixture for the engine cylinder. If the carburetor runs rough because it's clogged or dirty, you can clean and rebuild it, using a manufacturer-approved replacement kit. The kit includes gaskets, seals, a hinge pin and other components that you might need to replace. You probably won't use every part in the carburetor kit. In this repair, you use the fuel bowl gasket, mounting gasket and hinge pin.

Use these steps to rebuild the carburetor on common Briggs & Stratton engines that power Craftsman, Troybilt, Husqvarna, MTD, Poulan, Toro, Murray, Snapper, Yard-Man and John Deere riding mowers and lawn tractors.

If the riding mower carburetor is too corroded, dirty or damaged to rebuild, you can replace it with a new one. See How to Replace a Carburetor in a Riding Lawn Mower.

Repair difficulty:
     
Time required:

Less than 60 min.

Parts Required

  • Carburetor rebuild kit

For manuals, repair guides, and specific part recommendations, enter your model number.

Tools Required

  • Wrench set
  • Nut driver set
  • Punch set
  • Hammer
  • Pliers
  • Hose pinch-off pliers
  • Carburetor cleaner
  • Compressed air
  • Thin wire or paper clip
  • Shop rags
  • Fuel-safe container
  • Petroleum jelly
  • Safety goggles
  • Work gloves

Before you begin

Let the engine cool.

Park the tractor on a level surface in a well-ventilated area and set the parking brake.

Wear work gloves to protect your hands and safety goggles to protect your eyes.

 

Instructions

 Warning: Undertaking repairs to power lawn-care equipment can be hazardous. Use the proper tools and safety equipment noted in the guide and follow all instructions. Do not proceed until you are confident that you understand all of the steps and are capable of completing the repair. Some repairs should only be performed by a qualified technician.

How to Rebuild a Carburetor in a Riding Lawn Mower

Step 1: Disconnect the battery

Turn the ignition switch off and remove the key.

Lift the seat.

Remove the bolt connecting the negative cable to the battery and tuck the cable away from the battery so it doesn't touch the battery post.

Step 2: Remove the engine blower housing

Lift the tractor hood.

Remove the air duct mounting screws and pull off the air duct.

Turn each air filter cover retaining knob counterclockwise and pull off the air filter cover.

Remove the air filter.

Remove the air filter housing screw.

Remove the front and rear blower housing mounting bolts and lift off the blower housing.

 Tip: Remove the hood to gain more room to work.

Step 3: Disconnect the fuel line

Clamp off the fuel line with hose pinch-off pliers.

Place a shop rag under the carburetor end of the fuel line to catch drips.

Release the clamp that attaches the fuel line to the carburetor and pull the fuel line off the carburetor.

Wipe up any spilled fuel.

Step 4: Remove the carburetor

Remove the air intake mounting nuts.

Detach the breather tube and remove the air intake.

Disconnect the wire from the fuel solenoid.

Take a digital photograph of the carburetor linkage connections to document their location for reassembly.

Remove the carburetor mounting studs.

Disconnect the throttle rod and the throttle spring.

Disconnect the choke rod.

Pull off the carburetor and place it on a clean work surface in a well-ventilated area.

Step 5: Remove components

Unthread the solenoid valve and remove it.

Remove the float bowl, draining fuel from the float bowl into the fuel-safe container.

Punch out the float hinge pin.

Remove the float and needle valve.

Remove the float bowl gasket, engine intake gasket and air intake O-ring. 

Step 6: Clean the carburetor

Clean the float bowl and gasket seating surfaces using carburetor cleaner and a shop rag.

Use a paper clip to remove any float bowl gasket and air intake O-ring residue.

Use carburetor cleaner and a paper clip to clean all the holes in the carburetor, paying close attention to the main and idle jets.

Let the carburetor dry completely before reassembling it (at least 10 minutes).

Step 7: Reassemble the carburetor

Lubricate the new float bowl gasket with a small amount of petroleum jelly.

Install the new float bowl gasket.

Install the new needle valve.

Reattach the float with the new hinge pin.

Attach the float bowl with the solenoid valve.

Install the new air intake O-ring.

Step 8: Install the rebuilt carburetor

Position the rebuilt carburetor near the engine and reconnect the choke rod.

Connect the throttle rod and spring.

Install the new intake gasket on the engine.

Attach the carburetor on the engine with the mounting studs. Tighten the studs firmly.

Connect the fuel solenoid wire.

Attach the breather tube to the air intake and connect the air intake to the carburetor.

Install the air intake mounting nuts.

Reattach the fuel line to the carburetor with the hose clamp.

Release and remove the hose clamp pliers from the fuel line.

Step 9: Connect the fuel line

Attach the fuel line to the carburetor.

Remove the hose pinch-off pliers from the fuel line.

Step 10: Reinstall the engine blower housing

Position the blower housing on the engine and align the air diverter in the housing.

Install the blower housing mounting bolts.

Install the air filter housing screw.

Install the air filter and air filter cover.

Install the air duct and attach it with the mounting screws.

Lower the tractor hood.

Step 11: Connect the battery

Reconnect the negative cable to the negative battery terminal.

Lower the seat.