Model #XR-35 Brother mechanical sewing machines

  • No Image Available - Wards
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

I replaced the heating element on a whirlpool built in electric oven but the new element does not work. Are there other parts that tipically go bad?

A:

You could have blown oven shut-down thermal fuse in that circuit. The wiring diagram in the first image below shows that component circled in red for the upper oven. The lower oven has a similar fuse. The physical location of those fuses is shown in the second image. You would need to shut off the house circuit breakers for the oven and pull it out of the cabinet to access those fuses. They are located on the outside back wall of the oven cavity. Remove the outer back panel on the oven to access that component. If those fuses are okay, then you could have a bad relay on the electronic oven control board. The relays are circled in green and blue. The location of that control board is in the console. It is mounted behind the control panel. A wiring failure in that circuit could also prevent the element from heating.

You can order parts from this page: Whirlpool Oven Model GBD307PDS09 Parts . Be sure that you shut off the house circuit breakers for the oven before accessing internal components and replacing parts.

I hope that this information helps. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
November 20, 2012
Q:

What was the original price for a craftsman table saw xr 2412 (113.298032)? How much did it weigh and does it have a cast top?

A:

That saw retailed for $399.88. I don't have a specification on the weight but it is probably close to 300 lbs. It does have a cast iron top.

Read More
Lyle W -
Sears Technician
May 09, 2013
Q:

What does F 35 Mean on Washer

A:

Here is that parts image that is missing from the expert answer provided above.

Read More
Lyle W -
Sears Technician
June 09, 2011
A:

The images below show that air pressure hose. It is a black hose connected to that pressure switch. The other end is connected to the air trap on the bottom of the washer tub.

Read More
Lyle W -
Sears Technician
June 23, 2011
A:

Hello Steven. Thanks for providing that model number. The F35 code on your washer indicates a failure of that water level pressure sensor as noted in the above thread. The part number for that component in your washer is W10415587. You can order that part by clicking on the Find Parts link at the top of this page. If you need more help, reply with additional details.

Read More
Lyle W -
Sears Technician
August 07, 2011
A:

Hello Darcie. Biguggy is correct in the above response. The part number for that pressure switch that is likely causing the F35 code is W10415587. I added a direct link for that part below this response. Biguggy is also correct about checking that air hose tube that goes from that pressure switch to the bottom of the washer tub. You can UNPLUG the washer and remove the top panel to access that pressure switch. Screws at the very back of the top panel can be removed and then you can pull that top panel back and off of the washer. The location of that pressure switch is shown on the first page of this thread. If you find no problems with that air tube, then replacing that pressure switch should fix this problem. If you need more help, let us know.

Read More
Lyle W -
Sears Technician
October 16, 2011
A:

Hello J.R. Yes that same water level switch (part W10415587) is likely causing your problem. Check for excessive suds in the washer before you replace that switch. If you are using too much detergent or you are using non-HE (High Efficiency) detergent then the excessive suds could be causing the SUD and the F35 error codes. If you do not see excessive suds present then replacing that water level switch should fix your problem. If you need more help, let us know.

Read More
Lyle W -
Sears Technician
October 19, 2011
A:

You are probably referring to the large item filter on the drain pump that is shown in the image below. It would not hurt to clean out that filter if you still have the bottom front service panel off of the washer (and the washer still UNPLUGGED). Be sure that you place a shallow pan (baking pan) under that opening before removing that large item filter from the pump. You may find some coins or lint in that area. There is sometimes a build-up of mildew that may need to cleaned out using a liquid chlorine bleach and water solution. Use protective gloves when handling that bleach and water solution. If the washer is draining properly and you want to skip that procedure, then it should not matter. If you need more help, let us know.

Read More
Lyle W -
Sears Technician
October 19, 2011
A:

The model number is normally located on the front panel around the opening to the tub. Open the door to view that area.

Read More
Lyle W -
Sears Technician
September 18, 2012
A:

I have not heard of any common problems caused by adding power such as Oxy Clean directly to the tub. It sounds like you had an usual situation. Adding Oxy Clean or other powders to directly to the tub should not interfere with the air path between the air trap and the water level pressure transducer in most circumstances. Thanks for letting us know what you found. If you need more assistance, let us know.

Read More
Lyle W -
Sears Technician
September 19, 2012
See more answers