Model #X2-V182BK Jvc compact disc

  • No Image Available - Wards
    3 Results

Question and Answers

Q:

I can't program the remote garage door openers and the keyless entry pad. One or the other works but not both. What causes this?

A:

The logic board in your garage door opener is security +, rolling code technology. The keyless entry you bought is probably billion code technology. The logic board will accept either billion code or rolling code remotes and keyless. It will not accept both at the same time.

You need to get a 53684 keyless entry for rolling code technology.

Read More
Jimmy K -
Sears Technician
Q:

Kenmore Elite smartheat quietpak9 HE4 electric dryer mod#11085872400 beeps once, wont start...

A:

Thank you for your question and I understand your concern.

Based on your symptom and details, I suspect a faulty thermal fuse. If the thermal fuse is open/faulty; the dryer will not start. The thermal fuse #3392519 for model 110.85872400 can be ordered from Sears Parts Direct if you find it open.

The thermal fuse can be disconnect and tested for continuity with an Ohm meter. I added an image below showing where it's located and how to access the thermal fuse. NOTE: Disconnect the power cord from the power source before removing the lower front access panel.

This may be the issue. If not, please reply and I will be glad to assist you further.

Read More
Joey S -
Sears Technician
September 26, 2012
A:

Joseph: Replacing the thermal fuse will likely resolve the problem. Let me know what happens. Thanks

Read More
Joey S -
Sears Technician
September 28, 2012
A:

Joseph: A thermal fuse can measure continuity but under a current load it can open. You might want to try disconnecting the thermal fuse and add a temporary insulated jumper wire between the two wire leads and then see if will start. If it does not start, make sure the belt is intact because if the belt it broken or has come off; the motor will not start. If the belt is intact then I would suspect a faulty control board. You can check the control board with a voltage meter. There are two blue wires on the control board and when start it press, there should be 120 volts measured across the two blue wires at P1 connector. If you do not feel safe and confident in measuring the voltage, I suggest calling a service technician. When start is pressed you should also hear the motor relay on the control board make a faint click. If you do not hear a faint click, the control is likely faulty but be sure to make the voltage check before condemning the control board.

Read More
Joey S -
Sears Technician
September 29, 2012
A:

Joseph: Be sure it was the thermal fuse you tested and not the thermistor. Make sure its the thermal fuse that you jump out and by pass. Based on the click, the thermal fuse is likely faulty.

Read More
Joey S -
Sears Technician
September 29, 2012
A:

Joseph: Good, I was just making sure you were testing the thermal fuse and not the thermistor.

Read More
Joey S -
Sears Technician
September 29, 2012
A:

Joseph: Sometimes it is best to get a technician. In order to continue diagnosing the failure will require a voltage meter. The voltage will need to be measured at the control board after pressing start. It could have a faulty control board or door switch even though the light comes on and goes off.

Read More
Joey S -
Sears Technician
October 01, 2012
See more answers
Q:

why won't my Kenmore washer start?

A:

Barbara H. provided a link for the owner's manual in the above response. You may also need the operating manual pages that I provided in the first 3 images below. The owner's manual in the above link does not have information that is provided below for operating the controls.

Page 2 of the operating instructions show how to enable/disable the control lock function on this washer. Your symptoms suggest that the control lock function may be enabled. You indicated that you pressed the OPTIONS and SELECT buttons but that had no affect on the controls. If you did not press and hold those buttons at the same time for 10 deliberate seconds (or slightly longer), then I recommend that you try using that procedure to disable the control lock function on the washer.

If that does not help, then your control may be signaling an error code. Reply with additional details if the above information does not help you.

Read More
Lyle W -
Sears Technician
March 28, 2011