Model #VR-407-S Kenwood receivers

  • Cabinet Parts
    3 Results

Question and Answers

Q:

(code F50 ) Put power to the washer after 2 days. Washer ran from 40-7 minutes,stopped on the spin cycle with the 7 flashing , then lost power.

A:

Hi Reggie,

Thank you for submitting a question to Manage My Life.

The F4 error is a recirculation pressure switch failure. This error code and its causes are explained on the tech sheet I included in my previous response. This document also contains the diagnostic testing procedures for your washer. Here is a link to your previous question; model # 110.22036100 code 50 and now no power kenmore . This particular washer does not have an error code containing 50. The "50" you saw was most likely the time display.

You will now need to check for;

  1. Plugged recirculation hose (black hose).
  2. Plugged or disconnected air tube (clear tube).
  3. Wires to the recirculation pressure switch disconnected or not connected correctly.
  4. Failed recirculation pressure switch. Switch (black wire, tan wire) contacts should be open with pressure applied and closed with no pressure.

I am including the disassembly instructions for this washer in the images below.Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts.

The diagnosis of this issue will require the use of an ohm/volt meter and you will have to perform ohm checks and/or live voltage checks. If you have an ohm/volt meter and are confident in your technical abilities, please reply below and I will be happy to assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram and for parts purchases; Sears Parts Direct .

I hope this is helpful. If I may be of further assistance please reply to this post.

Landell

Read More
Landell -
Sears Technician
November 30, 2011
A:

Hi Reggie, Glad to hear you are up and running. Please keep Manage My Life in mind for all of your do-it-yourself projects. Landell

Read More
Landell -
Sears Technician
December 05, 2011
See more answers
Q:

kenmore s/s fridge

A:

I don't have an illustrated procedure or video that replacement of that cold control thermostat in your Kenmore refrigerator. The parts diagram of the control section is shown in the image below. You will need to rely on that parts diagram and your personal observation of the control area to determine how to complete this repair. Unplug the refrigerator to disconnect electrical power before beginning this repair. Safely store the food if necessary. You can look for screws under that control housing that will release it so that it can drop down. Once you release that control housing, you should be able to remove the wiring from the old cold control thermostat and pull it out. Observe how the sensor is positioned as you pull the old thermostat out. You will need to route that sensor for the new thermostat in the same manner.

I hope that this information helps. If you need more assistance, reply with additional details.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
December 12, 2011
Q:

How do I disconnect the clock display on my Kenmore range model 911.4528813?

A:

To disconnect the clock, turn off the breaker to the range to disconnect electrical power. Raise the main cook top. Remove the screws that secure the wire covers on the back of the console. You may also need to remove screws from the burner box in order to remove the wire covers. Pull the wire covers out of the way to access the wire connections to the clock. Pull on of the wires off of the clock and tape the end with electrical tape or attach a wire nut to insulate the end of the wire so that it does not short against the cabinet. Reassemble the range and turn the breaker back on.

Read More
Lyle W -
Sears Technician