Model #UFS-7EVP.004 Amana microwave commercial

  • Replacement Parts
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Schematic
    3 Results

Question and Answers

Q:

Adjusting valves on craftsman lt1000

A:

Thank you for your question.

 

I will be happy to assist you. I looked up the model number of the engine on your tractor. The engine should be model 31C707-0230-E1. If this is the correct model number, the valves should be set to 0.004. I found a great video that shows how to adjust the valves. Click here to watch the video.

I hope this is helpful. Please let me know if you need further assistance.

 

Thank you for using Manage my life.

Mark. 

Read More
Mark T -
Sears Technician
August 31, 2013
Q:

How to adjust intake valves Craftsman LT1000 Model 917.272072

A:

Thank you for your question.

I am sorry you are having a problem with the tractor. I will be happy to assist you in setting the valve lash. I have posted an image below that contains the instructions for setting the valve lash. Click on the image to enlarge it.

If you still have problems with the tractor after setting the valve lash feel free to reply below with more details. I will give you more assistance in diagnosing the problem.

Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
September 01, 2011
A:

I am sorry you are still having a problem. If you are sure the engine was on top dead center when you adjusted the valves they should be ok. Another possibility is a sheared flywheel key. If the key is sheared the spark is not delivered at the correct time. To check the key you will need to remove the top cover on the engine. Then remove the bolt securing the flywheel. The key way in the crankshaft and the flywheel should be aligned. If they are not the key is sheared. If it is fine, try pouring a small amount of fuel into the throat of the carburetor and try to start the engine. If the engine starts and stalls the problem is fuel related. Please let me know what you find with these checks and I will assist you further.

Read More
Mark T -
Sears Technician
September 03, 2011
See more answers
Q:

I have an error message E0 - F5 on my gas range, door won't unlock

A:

Thank you for your question.

Having the oven door locked and you cannot get it open is a real concern.

Since you were in the self clean mode it may have caused a problem with the door light switch circuit when it came up with a F5 error code.

Since the door is locked, and pushing the cancel button after re-setting the power did not help, we will need to get to the lock mechanism.

  • If you feel comfortable with and have some mechanical ability, I can help you get the door unlocked.

  • First REMOVE POWER to the range.

  • Pull the range out from the wall and locate and remove the screws that secure the back panel on the range.

  • Locate the lock rotor mechanism just below the control panel. I have given a picture below.

  • You will need to remove the screws that fasten the lock rotor to the range.

  • Turn the rotor mechanism at an angle so you can pull out the lock rod on the rotor. This will release the door hook, so you can get it open. With the door open re-install the lock rotor rod and fasten back onto the range.

  • With the door now open you can locate the door switch and with a sharp tool get in behind the edge and push in to release the tabs on the door switch and pull out.

Examine the door switch wires from the switch connections back to the control board. If they look ok then replace the door switch.

  • Replace the door switch with part number;3196262 and if the door switch wires are ok it should fix your problem.

You can order the door light switch from;Sears Parts Direct .

  • Once you have the light switch replaced and you have the range powered back up push on the door switch with your thumb and hold and put the range in self clean for 30 seconds and then cancel the clean cycle to reset the door hook.

  • Re-install the back cover and put range back into position.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

I hope this will help.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
December 21, 2010