Model #TRIMMY HIT Husqvarna trimmer head

  • Page 1
    3 Results
  • Page 2
    3 Results
  • Page 3
    3 Results
  • Page 4
    3 Results
  • Page 5
    3 Results

Question and Answers

Q:

Why won't my dryer come on when I hit start?

A:

The wiring diagram for your dryer is shown in the image below. This diagram shows several components that could prevent your dryer from running. Since the timer buzzes when the start button is pushed, this indicates that the start button and the door switch is okay. The components that could prevent the dryer from running include:

  • Thermal fuse
  • Drive belt or belt switch
  • Wiring between components
  • Failed drive motor
I recommend unplugging the dryer and pulling up the top of the dryer as shown in the left side of the second image to check the drive belt. If the drive belt is okay, then I recommend checking the thermal fuse (with the dryer still unplugged). You can access the thermal fuse by removing the back panel of the dryer. The thermal fuse is located on the blower housing as shown in the third image (your dryer will have a thermostat beside the thermal fuse instead of a thermistor and the wire colors will be blue). To check the thermal fuse, remove one wire and measure the resistance across the leads of the fuse. You should measure near zero ohms of resistance (continuity). If you measure infinite resistance (open), then the fuse is blown and will need to be replaced. You can order a new fuse from the Sears PartsDirect website. The part number for your thermal fuse on this model is 3392519. To check for proper motor run and verify this failure, you can connect the wires from the thermal fuse and tape them with electrical tape. Reassemble the dryer and see if it runs. Do not leave this fuse bypassed. This is an important safety component in the dryer. Replace the fuse before continuing to use the dryer.

If the thermal fuse and belt are both okay, then a failed drive motor or a wiring failure would be preventing your dryer from running.

If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
Q:

Can there be a short in the sensor from a lightening hit?

A:

Don is correct. You probably have a problem with that logic control board in the motor unit. You will probably need to replace that logic board or replace the whole garage door opener.

If you need more help, let us know.

Read More
Lyle W -
Sears Technician
August 19, 2011
A:

Hello Tom. Here are some tips that may help: Check the batteries in all of the remotes. You may need to change all of the batteries. Once you change those batteries, see if the remotes work properly. If not, try reprogramming the remotes. If necessary, erase all codes and then reprogram all of the remotes.

Read More
Lyle W -
Sears Technician
August 29, 2011
A:

Hello Jen. I see that you posted a model number. Did you need more help with your garage door opener problem? Let us know. Thanks.

Read More
Lyle W -
Sears Technician
August 29, 2011
A:

Hello Doris. I apologize for the confusion about this remote. The part number that you need from Sears PartsDirect.com is 53753 (the model number 139.53753 without the "139." prefix. I provided a link for that part below this response. The store should also have that remote but they may be out of stock or cannot determine the correct one that you need. The part 41A5076-2 is an outer case for the above part 53753 but it does not contain the circuit board. I recommend that you order the 53753 or go back to the store and get the correct remote if they can help you find it. It is a 315 Hz Security + remote. Once you get the new remote, you can follow the steps shown in your owner's manual to program it. The second link below is a PDF of your owner's manual in case you need it. Let us know if you need more help.

Read More
Lyle W -
Sears Technician
August 30, 2011
A:

I have heard of problems with universal remotes having trouble synchronizing with the garage door opener motor unit. Since the keyless key pad was able to synchronize with the motor unit, that garage door opener logic control board should be okay. I have not heard of problems where it will program one remote and not others unless there are weak batteries in one of the remotes. In that situation, replacing the batteries in all of the remotes and then erasing all codes and reprogramming all remotes usually fixes the problem. I you get that Sercuity + 315 Hz remote described above and you can program that to work with your garage door opener, then I suspect that you have a circuit board problem with the home link system in your Traverse. You may try this: completely disconnect the battery in the Traverse to reboot the computer systems in that vehicle. If the circuit board that controls the home link system is locked up, this may free it up to work properly. You may need to reset the clock and possibly other systems in the Traverse if you do that so you may need to have your owner's manual available if you try that step to resolve the synch problem with you home link system. I hope that this additional information helps. Let us know if we can assist you further.

Read More
Lyle W -
Sears Technician
August 31, 2011
See more answers
Q:

Mower hit a rock

A:

Thank you for your question.
I am sorry you are having a problem with the mower. Usually when you hit a rock large enough to stop the engine, it will shear the flywheel key. If this happens, the engine will kick back and try to pull the starter rope out of your hands. They usually will not start either. To cure this, the flywheel key has to be replaced. This type of repair can be tricky if you do not have a flywheel puller. I was able to find a video that shows the steps to replace the key. Click here to watch the video.

If you need to order the key, you can do so from the following link. Craftsman mower parts


If you do not feel confident repairing this problem yourself, then you can have it repaired by a Sears technician. Here is a link that will provide the nearest drop-off locations: Sears Home Services .


I hope this helpful. Please let me know if you need further assistance.


Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
June 06, 2012