Model #SPA361-SERIES 1-2 Snapper walk behind lawnmower, gas

  • Loop Handle/control Series 1 & 2
    3 Results
  • Tracking Control
    3 Results
  • Oil Tank (model Splh231khe)
    3 Results
  • Oil Tank (all Except Splh231khe)
    3 Results
  • Tank Bracket
    3 Results
  • Fuel Tank
    3 Results
  • Rear Deck
    3 Results
  • Pump And Shelf
    3 Results
  • Hose
    3 Results
  • Power Unit Idler
    3 Results
  • Traction, Rear Wheel
    3 Results
  • Engine
    3 Results
  • Caster, Wheel And Tire
    3 Results
  • 36" Mower Deck (fixed Height)
    3 Results
  • 36" Mower Deck (adjustable Height)
    3 Results
  • 48"/52" Mower Deck (fixed Height)
    3 Results
  • 48"/52"/61" Mower Deck
    3 Results
  • 48"/52"/61" Mower Deck
    3 Results
  • 36" Deck Idler
    3 Results
  • 48"/61" Deck Idler
    3 Results
  • 52" Deck Idler
    3 Results
  • Cutter Housing
    3 Results
  • Decals-left & Right Panels
    3 Results
  • Decals-instr./caution/wrng/dngr
    3 Results
  • Electrical Wiring (manual Start)
    3 Results
  • Electrical Wiring-loop Handle
    3 Results
  • Wiring Schematic (manual Start)
    3 Results
  • Wiring Schematic (electric Start)
    3 Results

Question and Answers

Q:

My Kenmore 90 series washer agitator rocks back and forth around 1 to 2 inches.

A:

Thank you for your question and I understand your concern.

I must assume just the upper augur portion of the agitator is loose. It is not abnormal for the augur to rock back and forth a little bit but not 2 inches. You will need to remove the augur and check for any broken parts.

I added an image of the agitator assembly below. To remove the auger:

  • Remove the fabric dispenser
  • Remove the spring retainer (key#20) using the square end of a 1/2 inch ratchet extension. Turn the spring retainer counter clockwise (CCW) until it can be removed.
  • Grasp the augur and lift it up and off.
  • Lay your hand over the top of the augur and flip it upside down.

Replace any parts that appear damaged or broken and reverse the procedure. Use the image below in order to see the order of the parts. You will likely need to order part #8537433 which can be ordered from Sears PartsDirect

Read More
Joey S -
Sears Technician
September 13, 2011
Q:

Need insight on repairing a new, 1 1/2 year old micriwave

A:

Hello Al. You could have an internal wiring problem or another component failure such as a blown fuse that is preventing the microwave from working. I recommend that you have a service technician diagnose and repair that type of failure. Microwaves contain high-voltage components that can retain a lethal electrical charge of up to 2200 VAC -- even when the microwave is unplugged. Repairs and adjustments, even minor ones such as replacing fuses, can cause microwave leakage. A microwave shielding leakage test should be performed after any microwave service. It is for these safety reasons that we are unable to guide you in microwave repairs and instead recommend scheduling service with a qualified service technician. You can schedule service online with Sears Home Services or by calling 1-800-4-MY-HOME. We thank you for your understanding in this matter and hope we can help you with other questions and repairs in the future.

Read More
Lyle W -
Sears Technician
April 03, 2012
Q:

air condensor model#CA1030QKA1 What is it's size (1 1/2 or 2 TONS) ?

A:

According to the model number, this outside unit has a capacity of 2.5 tons.

Read More
Lyle W -
Sears Technician
May 19, 2010