Model #SILVER EAGLE 9-II Mcculloch line trimmers/weedwackers, gas

  • Replacement Parts
    3 Results

Question and Answers

Q:

wwhirlpool ultimate care II dryer wont start

A:

Thank you for your question and I understand your concern.

Without having the model number of your Whirlpool dryer I will have to assume the back is not designed to come off. If the lint filter is located on the top of the dryer, it will have a removable back panel. If the lint filter is located inside the dryer at the front lower area of the drum opening, then the front panel must be taken off to access the components. Some models will have a lower front access panel that is designed to come off to access the components.

If you model does not have a front lower access panel, then control panel will need to be placed in the service position in order to access and remove the screws towards the back of the top panel. Once the screws have been removed, slide the top forwards and lift it off. The front panel is fastened to each side panel near the top. Remove the screws and disconnect the door switch harness. Tilt the top of the front panel towards you and then lift it up and off. NOTE: Disconnect the power cord from the power source before servicing.

I added a couple of images below to reference.  I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post along with the model number.

 

Read More
Joey S -
Sears Technician
September 25, 2013
A:

Bill: Your model appears to have a front lower access panel located below the door that will come off to access the components. I added an image below showing how to remove the front access panel.

Read More
Joey S -
Sears Technician
September 26, 2013
A:

Bill: If you're certain the push to start switch where the two blue wires measures continuity when pushed and the thermal fuse is measure continuity as well as the door switch (blue and white). Then it could be a timer failure or motor failure. Also, if the belt is broken, the dryer will not start. I added an image below of the wiring diagram if needed. You may want to consider calling a service technician to diagnose and repair your dryer. A voltage measurement will likely have to be made at the motor while the start switch is pushed and held across terminals 4M and 5M. If not voltage is measured, the timer is likely faulty more so than the push to start switch. If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service by calling 1-800-4-MY-HOME. NOTE: I do not recommend making any voltage measurements unless you have experience and feel safe and confident in doing so, otherwise I strongly suggest calling for service.

Read More
Joey S -
Sears Technician
September 30, 2013
See more answers
Q:

Gas line/hose 143986700 Craftsman Engine

A:

Thank you for your question.

 

 

I am sorry you are having a problem with the engine. I will be happy to assist you. I looked up the engine model number you submitted. This model has one fuel line that runs between the fuel tank and the carburetor. The part number for that fuel line is 29774 and can be ordered from the following link. Replacement fuel line for Craftsman engine model number 143986700.

 

 

The engine also have a crankcase breath hose that connects between the back of the air filter base and the top of the engine. If you need this hose, it is part number 32447 and it can be ordered from the following link.

Breather hose for craftsman engine model 143986700. 

 

 

I hope this is helpful. Please let me know if you need further assistance.

 

 

Thank you for using Manage my life.

 

 

 

Mark T. 

Read More
Mark T -
Sears Technician
September 03, 2013
Q:

lawn mower won't start. craftsman eagle 1. model 917389611.

A:

Thank you for your question.

Usually when the mower starts and stalls, right away or does not start at all it has a dirty carburetor. First, make sure the fuel is no older than 5 weeks old. I would think the fuel is fresh this late in the mowing season. Next check the air filter. If the air filter is plugged the mower may not run. If the air filter is clean and the fuel is fresh, I recommend cleaning the carburetor.

To clean the carburetor you have to remove the spark plug wire and tip the mower on to its side. Make sure the oil fill tube is towards the ground. Then remove the float bowl nut on the bottom of the carburetor. Some fuel will leak out so do this in a well-ventilated area. Remove the float bowl, clean it with carburetor cleaner, and dry it. Do not get carburetor cleaner on the rubber gasket. The cleaner will expand the rubber and renders it useless. Next, put the straw on the spray nozzle of the carburetor cleaner. Spray the cleaner in to the holes where the float bowl nut came from. These are the fuel pick up tubes. Once those are flushed, clean the holes on the float bowl nut. I recommend cleaning the holes with bread tie wire and carburetor cleaner. Then assemble the carburetor.

Tip the mower back up right and test the operation. If the engine does the same starting and stalling, I recommend replacing the carburetor.

I had a customer send me a link to video he found that shows how to clean the carburetor. The engine is not exactly the same as yours but it will give you a general idea. Here is a link to that video

I hope this is helpful.

If you need further assistance, please reply with more details below.

Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
October 23, 2011