Model #Q90-125 SERIES 2 Dunkirk boiler-storage tanks

  • Cabinet Assy
    3 Results
  • Burner Assy
    3 Results
  • Boiler Block Assy
    3 Results
  • Exhaust Tee/trap Assy
    3 Results
  • Air Pressure Assy
    3 Results
  • Gas Valve Assy
    3 Results

Question and Answers

Q:

Why do I have 2 oil caps on my 850 Series 17" tiller?

A:

Without the model number of your tiller, I am not able to see the exact model that you have. Based on your description, I think that you have a tiller model 917.297141 or a similar model. On this model, there may be caps that appear to be oil caps. The lower cap will normally be yellow and has "oil fill" embossed in the cap. This is the cap that you should use to pull and fill the crankcase with oil. You do not need to use the plug that is above this oil fill cap. Follow the instructions in your owner's manual for draining and filling the oil. If you have a model 917.297141 and do not have the owner's manual, here is a link for your manual: Owner's Manual

If you have a different model or need more help, resubmit your question with additional details and the full model number of your tiller.

Read More
Lyle W -
Sears Technician
April 23, 2009
Q:

My Kenmore 90 series washer agitator rocks back and forth around 1 to 2 inches.

A:

Thank you for your question and I understand your concern.

I must assume just the upper augur portion of the agitator is loose. It is not abnormal for the augur to rock back and forth a little bit but not 2 inches. You will need to remove the augur and check for any broken parts.

I added an image of the agitator assembly below. To remove the auger:

  • Remove the fabric dispenser
  • Remove the spring retainer (key#20) using the square end of a 1/2 inch ratchet extension. Turn the spring retainer counter clockwise (CCW) until it can be removed.
  • Grasp the augur and lift it up and off.
  • Lay your hand over the top of the augur and flip it upside down.

Replace any parts that appear damaged or broken and reverse the procedure. Use the image below in order to see the order of the parts. You will likely need to order part #8537433 which can be ordered from Sears PartsDirect

Read More
Joey S -
Sears Technician
September 13, 2011
Q:

Kenmore 700 electric dryer is not heating to dry clothes

A:

 Thank you for your question and I understand your concern.

If the thermal fuse was blown in the dryer, the dryer would not start and run. 

I'm not sure what type of 125/250v adapter that you have but, the dryer power cord must be connected to a 220 volt power source. If the dryer is not connected to a 220 volt power supply or if dryer lost the line 2 (L2) voltage supply, the dryer will run but it will not heat.

Will the power cord plug directly into the 220 volt wall receptacle?  In order to verify if the dryer is getting the 220 power supply, the voltage supply will need to be measured with a voltage meter at the back of the dryer where the power cord leads are connected. The voltage supply should measure 220 volts when measuring across the two outside terminals at the terminal block. If you have a neighbor that has voltage meter and if your neighbor has experience and feels safe and confident in doing so, the voltage supply will need to be measured and verified. To access the terminal block, disconnect the power cord and then remove the terminal block cover at the back of the dryer where the power cord connects. Once you have the cover taken off and see the three terminals, then you can plug the power cord in and then measure the voltage supply.  Again, the voltage supply is measured across the two outer terminals. NOTE: If the person is not experienced in measuring the voltage supply, I recommend calling a service technician to diagnose the failure.

I added a link with a video showing how to check for 220-240 volts at the wall outlet. 

 If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link:Sears Home Services.

Read More
Joey S -
Sears Technician
April 19, 2013