Model #PRECISION TIG 185 (11105 TO 11109) Lincoln welder

  • Welder Assembly
    3 Results
  • Case Front Assembly
    3 Results
  • Case Base And Fan Assembly
    3 Results
  • Arc Starter And Bypass Assembly
    3 Results
  • Center Assembly
    3 Results
  • Cover Assembly
    3 Results
  • Cart Base Assembly
    3 Results
  • Upper Cylinder Support Assembly
    3 Results

Question and Answers

Q:

Tig Welder

A:

I found 2 Craftsman High Frequency Arc Stabilizers listed in our parts system. You may find the part that you need on one of those listings. Here is the parts diagram for the model 113.201170: Craftsman High Frequency Arc Stabilizer Model 113.201170 Parts.

Here is the link for model 934.201190:  Craftsman High Frequency Arc Stabilizer Model 934.201190 Parts.

If you need more help, reply with additional details and the full model number of your High Frequency Arc Stabilizer. 

Read More
Lyle W -
Sears Technician
February 14, 2013
Q:

NO COLD WATER COMING FROM MY KENMORE 800 - HOSE NOT CLOGGED AND WATER IS ON. CAN YOU PROVIDE ME WITH A PART NUMBER SO MY HUSBAND CAN REPLACE THE PART.

A:

Hi Elizabeth,

Thank you for submitting a question to Manage My Life.

I am sorry you are having problems with your washer.

Without a model number I cannot give you any part numbers or specific help with your washer. The model number should be located under the lid or on the back panel.

James R provided you with a link above that covers the basics of where I would suggest you start.

If you will include your model number in a reply to this post I would be happy to provide you with specific help on your washer.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
June 13, 2011
A:

Hi Elizabeth, You did not mention whether or not this unit will fill with hot water. If it will not fill with hot or cold the issue could be the timer, door switch, wiring, or load sense switch. If the washer will fill with hot but not with cold it will most likely be an issue with the cold valve or wiring. The remaining checks will require the use of an ohm/volt meter. If you have a meter and are confident in your ability to safely perform these checks, reply to this post and I will be happy to assist you in any way I can. Thanks again for using Manage My Life. Landell

Read More
Landell -
Sears Technician
June 15, 2011
A:

Hi Elizabeth, Yes, the water or inlet valve is sometimes called a solenoid. The part number for the valve for your washer is W10175893. Below is a link that you may use to purchase the Valve. I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. Thanks again for using Manage My Life. Landell

Read More
Landell -
Sears Technician
June 18, 2011
A:

Hi Elizabeth, The remaining checks will require the use of an ohm/volt meter. If you have a meter and are confident in your ability to safely perform these checks, reply to this post and I will be happy to assist you in any way I can. With that being said, the most likely cause for this issue is the load sense switch. I would prefer having voltages checks to back up this diagnosis, but the load sense switch would be the next most likely component to cause this failure. The part number for the load sense switch is W10248240. Below is a link that you may use to purchase the Load sense switch. I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. Thanks again for using Manage My Life. Landell

Read More
Landell -
Sears Technician
June 18, 2011
See more answers
Q:

kenmore washer fills up with water at end of spin cycle, also agitator turns as soon as washer is started, it never did this before?

A:

Thank you for your question.

I am sorry you are having a problem with your washer. Usually when this happens, it is because of the load sense switch. The relay in the switch sticks and allows the washer to fill and agitate at the same time. A simple check is to access the load sense switch and unplugging the wires to it. Then check the operation. I have provided you with the instructions for accessing the load sense switch below. Make sure you unplug the washer first. Once the console is open the load sense switch it the switch that has the clear plastic hose connected to it. Remove the connector that has the violet, white and the blue with orange stripe from the switch. Then carefully plug the washer back in and start a wash cycle. If the washer does not do anything, you have to replace the load sense switch. If the washer still agitates, the problem is most likely a failed timer.

Please feel free to let me know if you need further assistance.

Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
December 13, 2011
A:

If the washer does not do anything with the connector removed, I recommend replacing the load-sensing switch. The part number for the switch is W10177795 and can be ordered from the link below.

Read More
Mark T -
Sears Technician
December 14, 2011
See more answers